Elma Modulgrav Скачать руководство пользователя | Manualshive

Страница: 14 / 24

background image

Quality from Tradition; Technology of Tomorrow

mbC:\DB-pdf\BedAnl\Modulgrav\-GB-300102.doc

14

5. step

Move the diamond close down to the ring
(approx. 5 mm) and fix it (1).

6. step

Place the copyring pin in the centre of letter.
Slide down the black plastic arrow (loosen the
knurled nut) (2) and set the distance of the
diamond so that it is positioned above the centre of
the ring.

7. step

Now push up the plastic arrow and start engraving.

Please note:

Choose your required size of engraving

Adjust the engraving pressure to the material you work on.

2

1

«
...
12
13
14
15
16
...
»

Содержание Modulgrav

























Отзывы:

Нет отзывов

Похожие инструкции для Modulgrav

Бренд: Qls Страницы: 53

Бренд: Xerox Страницы: 36

Бренд: Unitech Страницы: 18

Бренд: Unitech Страницы: 26

Бренд: Panduit Страницы: 6

Бренд: VASTEX Страницы: 15

Бренд: Oce Страницы: 255

Бренд: Oki Страницы: 572

proColor pro900DP

Бренд: Oki Страницы: 127

Бренд: Olivetti Страницы: 309

Бренд: OKIDATA Страницы: 4

Бренд: Compuprint Страницы: 38

8860MFPD - Multifunction Inkjet Printer

Бренд: Xerox Страницы: 16

Бренд: Black Box Страницы: 30

Бренд: Sam4s Страницы: 24

Accel-a-Writer 4

Бренд: Xante Страницы: 12

Бренд: Oki Страницы: 72

Бренд: Canon Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды