Eizo DuraVision MDU5501WT Скачать руководство пользователя страница 40

Страница: 40 / 41

Install the fan holder and fan cover.

Fan holder

Fan

Distribution cable

Label surface

Connector

1. Install the holder on the monitor.
2. Connect the distribution cable to the monitor. Ensure the connector is connected to the monitor.

Route the distribution cable through the gap of the fan.

Attach the cover to the monitor using the screws removed in step 2 (page

Note

•

After replacing the fan, perform the following procedure to check the operation:

Confirm that the fan is rotating.

Check that the message "WARNING: Fan not working" is not displayed on the screen.

Periodic check of buzzer alarm

•

The buzzer installed in this monitor can be activated to emit warning beeps by system-side control.

•

Check periodically to ensure that the warning beeps of the buzzer work. Use system-side control to
check the buzzer.

Note

•

For details on system-side control, contact your local EIZO representative.

Appendix

Содержание DuraVision MDU5501WT










































Результаты поиска

Содержание DuraVision MDU5501WT

Отзывы:

Похожие инструкции для DuraVision MDU5501WT

Бренды по названию

Популярные бренды

Eizo DuraVision MDU5501WT, Руководство по установке

Результаты поиска

Содержание DuraVision MDU5501WT

Отзывы:

Похожие инструкции для DuraVision MDU5501WT

Бренды по названию

Популярные бренды