Eizo DuraVision MDU5501WT Скачать руководство пользователя страница 38

Страница: 38 / 41

How to replace the cooling fan

Attention

• Be sure to follow the procedure when replacing the fan. Note that EIZO Corporation assumes no responsibility for

any damage caused due to incorrect handling of this product.

Note

• Please contact your local EIZO representative for replacement parts.

Disconnect the AC power cord and DC power terminal block.

Remove the fan cover and fan holder.

Fan holder

Screw M3 × 8 (four pcs)

Distribution cable

Fan cover

Fan

1. Remove the screws (four pcs) that secure the cover.

Use a box-end wrench with 3 mm nominal diameter (with offset) to remove the screws.

2. Remove the cover.

Disconnect the distribution cable connected to the monitor.

Remove the holder.
The holder is temporarily attached to the monitor using a face fastener.

Attention

•

Hold the connector when removing the distribution cable. Pulling on the distribution cable may damage the

connector.

Appendix

Содержание DuraVision MDU5501WT










































Результаты поиска

Содержание DuraVision MDU5501WT

Отзывы:

Похожие инструкции для DuraVision MDU5501WT

Бренды по названию

Популярные бренды

Eizo DuraVision MDU5501WT, Руководство по установке

Результаты поиска

Содержание DuraVision MDU5501WT

Отзывы:

Похожие инструкции для DuraVision MDU5501WT

Бренды по названию

Популярные бренды