Eizo DuraVision MDU5501WT Скачать руководство пользователя страница 13

Страница: 13 / 41

●

Installation requirements

Rear view

400.0

200.0

4. Connector

3. Air intake area

Unit: mm

2. Operation

7. Installation surface

1. Cooling fan

6. Mounting tapped hole

5. Buzzer

2. Operation

Name

Installation requirements

1. Cooling fan

•

Do not block the area around the cooling fans. Ensure there is

sufficient space around the cooling fans so that air can circulate.

2. Operation

•

Do not block the area around the operation.

3. Air intake area

•

Do not block the area around the air intake area. Ensure there is

sufficient space around the air intake area so that air can circulate.

4. Connector

• Do not subject the cable to any excessive load. Note that load on the

cable may damage the connector.

5. Buzzer

•

Do not block the area around the buzzer when using it.

6. Mounting holes (10 holes)

•

Mounting screws are not provided. Prepare 10 pcs of M8 (8 mm

nominal diameter) screws with thread pitch of 1.25 mm, separately.

•

Depth of the tapped hole is 15 mm. Embed the screw 12 mm to 15 mm

(inclusive) below the surface.

• Align the 10 mounting holes in the monitor with those in a table, etc.,

then secure the monitor using the screws. Be sure to fully tighten the

10 screws (recommended torque: 10 N·m to 12 N·m).

7. Installation surface

•

The installation surface must have a flatness of within 2 mm.

English

Chapter 2 Installation / Connection

Содержание DuraVision MDU5501WT










































Результаты поиска

Содержание DuraVision MDU5501WT

Отзывы:

Похожие инструкции для DuraVision MDU5501WT

Бренды по названию

Популярные бренды

Eizo DuraVision MDU5501WT, Руководство по установке

Результаты поиска

Содержание DuraVision MDU5501WT

Отзывы:

Похожие инструкции для DuraVision MDU5501WT

Бренды по названию

Популярные бренды