Echelon LONWORKS PLT-22 Скачать руководство пользователя страница 73

Страница: 73 / 128

EN 50065-1 measurements. One limit is measured using a quasi-peak detector,

the other using an average detector. Note that those limits are the same as

required for any other CENELEC compliant product, except in the

communication range of 110kHz to 140kHz where lower noise levels are

specified.

For FCC applications, the limit of figure 5.8 corresponds to FCC Class B limits

for frequencies above 450kHz. Below 450kHz, the limits are set such that the

full communication performance of the PLT-22 transceiver is maintained. Two

lines are indicated. The solid "single carrier" line shows the noise limits required

to maintain full performance if the transceiver is used only in its single carrier

frequency mode. If the PLT-22 transceiver is going to be used in its dual carrier

frequency mode, then it is recommended that the power supply noise fall below

the dashed "dual carrier" line. Meeting this criteria ensures that the full

performance of both operating frequencies is available to overcome unexpected

power line noise in either of the two frequency ranges. A quasi-peak detector

should be used when verifying power supply noise against the limit lines of

figure 5.8.

For both CENELEC and FCC measurements, the measurement bandwidths are

200Hz for measurements below 150kHz, and 9kHz for measurements above

150kHz, as described in CISPR 16.

ORKS

PLT-22 Transceiver's User Guide

5-13

Содержание LONWORKS PLT-22

































































































































Результаты поиска

Содержание LONWORKS PLT-22

Отзывы:

Бренды по названию

Популярные бренды

Echelon LONWORKS PLT-22, Руководство пользователя

Результаты поиска

Содержание LONWORKS PLT-22

Отзывы:

Бренды по названию

Популярные бренды