manualshive.com logo in svg

Echelon LONWORKS PLT-22, Руководство пользователя

Поделиться
Скачать
Echelon LONWORKS PLT-22 Скачать руководство пользователя страница 108

 

Table 7.1 

 Primary Frequency Receive Performance Verification Table 

 

Send 

Transmit 

Attenuatio

n (PLCA 

Attn) 

Overall 

Attenuatio

n (Attn + 

60) 

UnackPr

i Error % 

(expecte

d) 

UnackPr

i Error % 

(observe

d) 

UUT Pkts 

Received 

(observed) 

UUT  

Error % 

(expected) 

UUT  

Error % 

(1011 - #Rcvd)/10 

(observed) 

0 dB 

60 dB 

<1% 

 

 

<1% 

 

6 dB 

66 dB 

<2% 

 

 

<2% 

 

12 dB 

72 dB 

<3% 

 

 

<3% 

 

18 dB 

78 dB 

≥

3% 

 

 

≥

3% 

 

24 dB 

84 dB 

≥

3% 

 

 

≥

3% 

 

 

 

Table 7.2 

 Secondary Frequency Receive Performance Verification Table 

 

Send 

Transmit 

Attenuatio

n (PLCA 

Attn) 

Overall 

Attenuatio

n (Attn + 

60) 

UnackSe

c Error % 

(expecte

d) 

UnackSe

c Error % 

(observe

d) 

UUT Pkts 

Received 

(observed) 

UUT  

Error % 

(expected) 

UUT  

Error % 

(1011 - #Rcvd)/10 

(observed) 

0 dB 

60 dB 

<1% 

 

 

<1% 

 

6 dB 

66 dB 

<3% 

 

 

<3% 

 

12 dB 

72 dB 

≥

3% 

 

 

≥

3% 

 

18 dB 

78 dB 

≥

3% 

 

 

≥

3% 

 

 

The approximate signal attenuation between the Send PLCA-22 analyzer and Recv 

PLCA-22 analyzer shown in tables 7.1 and 7.2 is the sum of the attenuation level of 

the attenuator circuit and the 

Attn

 level of the Send PLCA-22 analyzer.  A properly 

performing product will show a low level of CRC errors (<3%) up to an attenuation of 

72dB between the two analyzers (66dB for secondary frequency).  Above these 

attenuations the error rate for the UUT should increase.  

If the results of this test are worse than expected, it is helpful to know if the problem 

affects only the performance of the UUT or if adjacent receivers are also impaired by 

the presence of UUT.  If the receive performance of the Recv PLCA-22 analyzer was 

worse than expected, disconnect the UUT and recheck the PLCA-22 analyzer error 

rate versus attenuation.  If it is determined that the presence of the UUT impairs the 

performance of the PLCA-22 analyzers then the UUT may be injecting noise back 

onto the power line.  Note that the same symptoms would also be observed if no 

7-16 

 

Communication Performance Verification

 

Содержание LONWORKS PLT-22

































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды