Echelon LONWORKS PLT-22 Скачать руководство пользователя страница 24

Страница: 24 / 128

Transmit Output Level

The TXLVL input pin on the PLT-22 transceiver determines the output voltage of the

transmit signal. When the TXLVL pin is left floating, the transceiver's open-circuit

output voltage is 3.5V p-p. When the TXLVL pin is grounded, the open-circuit

output voltage is increased by 6dB to 7Vp-p. The appropriate setting for TXLVL is

summarized in table 2.5.

Table 2.5

TXLVL Setting

TXLVL OUTPUT

VOLTAGE

APPLICATION

grounded

7Vp-p

Preferred mode of operation. Use for FCC,
Industry Canada, CENELEC class 134, Japan
MPT, and all dedicated wiring applications.

open

3.5Vp-p

Use for CENELEC EN50065-1 class 116
applications

TXON Output Signal

The PLT-22 transceiver provides an output signal suitable for controlling a PLA-21

Power Line Amplifier via the CKSEL1/TXON pin. The CKSEL1/TXON pin functions

as an input during the period in which the ~RESET pin of the PLT-22 transceiver is

held active (low). During the reset active period the logical states of the

CKSEL1/TXON and CKSEL0 pins are sampled and stored by the PLT-22

transceiver. The stored state is used to determine the frequency of CKOUT, as

described in table 2.4. After RESET becomes inactive (high) CKSEL1/TXON changes

to an output (CKSEL0 remains an input, but its state is ignored). The output, called

TXON, is a buffered version of the internal signal used to control the transceiver's

output amplifier. The TXON signal output is active high when the PLT-22

transceiver transmits packets.

The TXON signal is typically used to provide tri-state control of an external booster

amplifier, such as the PLA-21 Power Line Amplifier model 53001-01. For more

details see the

PLA-21 Power Line Amplifier Specification and User's Guide

2-10

Using

the

PLT-22

Transceiver

Содержание LONWORKS PLT-22

































































































































Результаты поиска

Содержание LONWORKS PLT-22

Отзывы:

Бренды по названию

Популярные бренды

Echelon LONWORKS PLT-22, Руководство пользователя

Результаты поиска

Содержание LONWORKS PLT-22

Отзывы:

Бренды по названию

Популярные бренды