Echelon LONWORKS PLT-22 Скачать руководство пользователя страница 48

Страница: 48 / 128

layout. The efficacy of the surge protection implemented in each product containing

the PLT-22 transceiver must always be verified empirically, since factors such as

PCB layout and packaging can influence the results as much as the choice of

protection components.

The level of surge protection required for a given product often depends on the

installed location of the product to be protected. Devices connected to branch circuits

within a building or home are typically subject to the lowest level of surge stress.

Devices connected at, or close to, the power entry point of a building or home, e.g.,

electrical meters and main breaker panels, are subject to higher levels of surge

stress. Devices connected to outdoor wiring are subjected to the highest surge stress

of all.

Standard tests for surge immunity are defined in IEEE C62.41-1991

and CEI/IEC

1000-4-5

. Both documents classify levels of surge stress by the type of surge wave-

form (either Ring wave or Combo wave), surge voltage, and surge current. In

addition to describing standard test methods, both documents also suggest surge

immunity levels for the device environments described above.

Comparison of the two documents reveals that their recommended test procedures

are identical, while the suggested immunity levels called out in IEEE C62.41-1991

substantially exceed the suggested immunity levels of CEI/IEC 1000-4-5. The more

severe (and thus more conservative) immunity levels called out in IEEE C62.41-1991

were used in characterizing the recommended surge protection circuitry shown in the

PLT-22 transceiver coupling circuit examples that follow.

The line-to-neutral coupling circuits documented later in this chapter have been

demonstrated to meet the IEEE C62.41-1991 "high system exposure" levels with no

damage for

branch circuit applications

power entry applications

, and

outdoor wiring

applications

, up to the limits of the available test equipment.

Table 4.1 summarizes the surge immunity of the PLT-22 transceiver in conjunction

with the specified line-to-neutral coupling circuits.

4-14

Coupling

Circuits

Содержание LONWORKS PLT-22

































































































































Результаты поиска

Содержание LONWORKS PLT-22

Отзывы:

Бренды по названию

Популярные бренды

Echelon LONWORKS PLT-22, Руководство пользователя

Результаты поиска

Содержание LONWORKS PLT-22

Отзывы:

Бренды по названию

Популярные бренды