Echelon LONWORKS PLT-22 Скачать руководство пользователя страница 12

Страница: 12 / 128

20kHz

40kHz

60kHz

80kHz

100kHz

120kHz

140kHz

160kHz

Electricity Suppliers

Consume

r Use

Consumer Use

"A"

"B"

"C" "D"

Restricted

With Protocol

No Protocol

Band Designations:

PLT-22

Primary

Signal

PLT-22

Secondary

Signal

Consumer Use

No Protocol

PLT-22

Secondary

Signal

PLT-22

Secondary

Signal

PLT-22

Primary

Signal

PLT-22 with

70 - 95kHz Operation

{

PLT-22 with

110 - 140kHz Operation

{

Electricity Suppliers

and Their Licensees

Figure 1.4

CENELEC Frequency Allocation

Audience

This document is intended for designers of products using the PLT-22 Power Line

Transceiver.

Content

This manual provides detailed operating instructions for the PLT-22 transceiver.

Related Documentation

The following documents are suggested reading:

PLT-22

Power Line Transceiver

data sheet (003-0250-01)

PLCA-22 Power Line Communication Analyzer User’s Guide

(078-0147-01)

PLA-21 Power Line Amplifier Specification and User’s Guide

(078-0161-01)

Centralized Commercial Building Applications with the L

ORKS

PLT-21 Power Line

Transceiver

(005-0056-01)

Demand Side Management with the L

ORKS

Power Line Transceivers

(005-0070-01)

Using the L

ORKS

PLT-22 Power Line Transceiver in European Utility

Applications

(078-0180-01)

1-6

Introduction

Содержание LONWORKS PLT-22

































































































































Результаты поиска

Содержание LONWORKS PLT-22

Отзывы:

Бренды по названию

Популярные бренды

Echelon LONWORKS PLT-22, Руководство пользователя

Результаты поиска

Содержание LONWORKS PLT-22

Отзывы:

Бренды по названию

Популярные бренды