Echelon LONWORKS PLT-22 Скачать руководство пользователя страница 32

Страница: 32 / 128

Table 3.2

Allowed Power Supply Types Versus Standard Transceiver Types

Standard Transceiver
Type Selection

Fixed V

power

supply <12.9V

Energy Storage V

power supply

>12.9V

PL-20C

Not allowed if the power supply design
relies on power management for worst
case duty cycle and load conditions

PL-20N

Not allowed if the power supply design
relies on power management for worst
case duty cycle and load conditions

PL-20C-LOW

Not allowed: node
may not transmit

PL-20N-LOW

Not allowed: node
may not transmit

LonBuilder and NodeBuilder PLT-22 Transceiver Channel

Definitions

To use the PLT-22 transceiver in dual frequency mode with the LonBuilder or

NodeBuilder tools, you must have

STDXCVR.TYP

file with a date stamp of 1999 or

later. PLT-22-based nodes built from a system with a

STDXCVR.TYP

file earlier than

1999 will transmit using only a single carrier frequency, even if it is blocked by noise.

To take advantage of the PLT-22 transceiver's ability to automatically change

frequency if the primary frequency range is blocked by noise, verify that the year on

the date of your

STDXCVR.TYP

file is 1999 or later. This file is located in the

ORKS

TYPES

directory (

c:\lonworks\types

by default) for the NodeBuilder

software, and in the LonBuilder

TYPES

directory (

c:\lb\types

by default) for the

LonBuilder software. If the date on your

STDXCVR.TYP

file is older than 1999, you

can download an update from Echelon's web site at www.echelon.com/toolbox.

Once you have verified that you are using the correct version of the

STDXCVR.TYP

file, specify PL-20N, PL-20C, PL-20N-LOW, or PL-20C-LOW as the standard

transceiver type in the NodeBuilder Device Template, as shown in figure 3.1, or the

LonBuilder Channel Create window. Select “Yes” for the “Enforce Standard Type”

field.

3-6

PLT-22 Transceiver Programming

Содержание LONWORKS PLT-22

































































































































Результаты поиска

Содержание LONWORKS PLT-22

Отзывы:

Бренды по названию

Популярные бренды

Echelon LONWORKS PLT-22, Руководство пользователя

Результаты поиска

Содержание LONWORKS PLT-22

Отзывы:

Бренды по названию

Популярные бренды