Echelon LONWORKS PLT-22 Скачать руководство пользователя страница 126

Страница: 126 / 128

B-8

Appendix B

Product Qualification - EMC

Item Check

When

Completed

Description

Proper measurement of conducted emissions is used to verify

compliance with FCC Part 15 and/or CENELEC EN 50065-1

as described in chapter 5.

Ω

//(50µH+5

Ω

) Line Impedance Stabilization Network

(LISN) as specified in

CISPR Publication 16

, second edition

is used for measurement.

The appropriate attenuator is used to ensure that the

transceiver's transmit signal does not overload the

measurement apparatus. The residual noise floor of the

entire measurement set is verified to be at least 10dB below

the specification limit (a noise floor less than 38dBµV for

FCC measurements, and a noise floor less than 36dBµV for

CENELEC EN 50065-1 measurements).

Measurements are made with a quasi-peak detector and the

average detector as specified in

CISPR Publication 16

FCC measurements are made with a 9kHz bandwidth filter

as specified. The CENELEC EN 50065-1 measurements are

made with a 200Hz bandwidth filter for measurements

below 150kHz, and a 9kHz bandwidth filter for

measurements above 150kHz.

For EN50065-1 verification all testing is done with a

Rohde&Schwarz EMI Test Receiver ESHS30 (or equivalent

tester with proper filter skirts) set to manual mode using a

set-up program described in chapter 5. Alternatively,

Hewlett Packard equipment is used with an appropriate

external filter.

Product Qualification - Electromagnetic Immunity and

Communication Performance

Item Check

When

Completed

Description

The product is tested to appropriate levels of either

CEI/IEC 1000-4-5, or IEEE C62.41-1991.

The product is verified to meet communication performance

capabilities per chapter 7.

Содержание LONWORKS PLT-22

































































































































Результаты поиска

Содержание LONWORKS PLT-22

Отзывы:

Бренды по названию

Популярные бренды

Echelon LONWORKS PLT-22, Руководство пользователя

Результаты поиска

Содержание LONWORKS PLT-22

Отзывы:

Бренды по названию

Популярные бренды