Echelon LONWORKS PLT-22 Скачать руководство пользователя страница 102

Страница: 102 / 128

Transmit Performance Verification

Use the following steps to verify that the transmit output impedance of the UUT is

low enough to adequately drive low impedance loads.

With a single PLCA-22 analyzer in idle mode (no packets being transmitted) and set

for C-band Internal and Line-to-Neutral coupling, connect the analyzer, the UUT,

the "5

Ω

load", and the Isolator as shown in figure 7.8 (if the UUT uses Line-to-Earth

coupling to a single power phase then the “7

Ω

load” should be used instead).

Verify that the UUT application program is not sending messages.

Press the service switch on the UUT.

Observe the primary signal strength LEDs on the PLCA-22 analyzer and check

which of the primary LEDs illuminate. If the UUT is configured for 3.5Vp-p

output (TXLVL, pin 21, on the PLT-22 transceiver is left open), all primary

signal strength LEDs up to, and including, the -6dB LED should flash for at least

6 out of 10 service pin messages from the UUT.

If the UUT is configured for 7Vp-p output (TXLVL, pin 21, on the PLT-22

transceiver is grounded), all primary LEDs up to, and including, the 0dB LED

should flash for at least 6 out of 10 service pin messages from the UUT.

Unit Under Test

(UUT)

service pin

PLCA-22

To power
mains

packet detect LED

ISOLATOR

2.4ž L-N Load

Isolated
Power
Line

5ž Load (7ž

load for sgl Ø L-E

UUT)

C-band

Figure 7.8

Transmit Performance Verification

7-10

Communication Performance Verification

Содержание LONWORKS PLT-22

































































































































Результаты поиска

Содержание LONWORKS PLT-22

Отзывы:

Бренды по названию

Популярные бренды

Echelon LONWORKS PLT-22, Руководство пользователя

Результаты поиска

Содержание LONWORKS PLT-22

Отзывы:

Бренды по названию

Популярные бренды