Eaton DS7 Series Скачать руководство пользователя страница 117 | Manualshive

Страница: 117 / 240

background image

4 Operation

4.8 LED indicators

DS7 Soft starter

09/16 MN03901001Z-EN

www.eaton.com

113

4.8.4.1 Error messages on start

Start (ramp) indicates the phase during which +A1 (and EN in sizes 3 and 4) is
activated and ramp time t-Start is active. This operating state is identical to
the phase in which, during continuous operation (TOR), control input +A1 is
switched o

ff

and delay ramp t-Stop (

≧

1) is active. The following error

messages may be issued in this operating state (start):

Table 21: Error messages on start

Message (PNU)

Errors

Possible causes

Remedy

Phase fault
(840.6310)

One phase missing on the
mains side

Fuse fault

Change fuse

Wiring defective

Control Wiring

Zero current detection
(860.0)

I

e

= 0 A

No power flow or current has
fallen below the thyristors’
holding current (

∼

0.5 A)

A motor is not connected or the
motor cable is broken

Check connection to T1, T2, T3

Heat sink overtemperature/
undertemperature
(860.16)

Heat sink temperature

≦

0 °C

or

≧

+80 °C

Device still overheated from last
start/stop

Wait for cool-down time to elapse; use fan
(DS7-FAN-032) if necessary

Excessively high control cabinet
temperature; fan filter soiled

Monitor the temperature in the control panel

Undertemperature; ambient air
temperature is too cold

Heat up the room or control panel and monitor
the temperature

Bypass contact not opening
(860.21)

• Bypass will not switch or

respond

• Bypass contact still

closed when a start
command is sent to +A1

• Bypass contact does not

open when +A1 is
switched off

Overload

Replace device; check dimensioning

Short-circuit in soft starter
output

Check motor feeder

Bypass contact does not close at
TOR
(860.21)

The bypass contact is not
closed after ramp time t-Start
(= TOR) elapses

• Internal fault in soft starter
• Defective control section or

relay

Replace device

Thyristor is defective
(860.20)

• Fuse fault
• Unbalanced phase

currents (> 30 %)

• Different voltage

magnitude between
input (L1, L2, L3) and
output (T1, T2, T3) during
operation (TOR)

Soft starter was overloaded
during last stop

Thyristor destroyed

Replace device; check dimensioning

Lightning

Exchange device; install lightning protection in
the installation

Supply voltage faulty
(860.19)

Excessively low voltage for
regulator supply
(U

s

< 20 VDC)

Overload of the external power
supply unit

Check dimensioning and overload of the power
supply unit

Supply voltage not available

Check control signals for switching the supply
voltage; install interlocks for start command if
necessary

No release (EN)
(860.2) – only sizes 3 and 4

An enable signal is not sent
when EN is activated

Heat sink temperature

≦

0 °C

Heat up the room or control panel and monitor
the temperature

Phase sequence error
(860.22)

Incorrect phase sequence

The power supply phases are
connected in the wrong
sequence.

Swap the phases

«
...
115
116
117
118
119
...
»

Содержание DS7 Series

















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DS7 Series

Бренд: NEC Страницы: 304

Бренд: YASKAWA Страницы: 256

SolarCell Remote

Бренд: Samsung Страницы: 2

Бренд: Samsung Страницы: 20

Бренд: Ohsung Electronics Страницы: 18

Бренд: Samson Страницы: 56

Бренд: Hach Страницы: 128

Бренд: Yamato Страницы: 33

Flashlight Blue

Бренд: Hama Страницы: 10

Бренд: Hama Страницы: 4

Бренд: Hama Страницы: 14

Бренд: Hama Страницы: 5

Бренд: ICP DAS USA Страницы: 166

Бренд: ICP DAS USA Страницы: 64

Tunnel Master Jr

Бренд: ICS Страницы: 83

PROFIBUS PROFI-2510

Бренд: ICP DAS USA Страницы: 4

Бренд: ICP DAS USA Страницы: 40

Бренд: Watts Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды