Eagle CUDA 350 S/MAP Скачать руководство пользователя страница 177

Страница: 177 / 180

NAVICO

LIMITED

ONE-YEAR WARRANTY

"We," "our," or "us" refers to EAGLE ELECTRONICS, a division of

NAVICO

, the manufacturer of

this

product. "You" or "your" refers to the first person who purchases this product as a consumer item

for

personal, family, or household use.

We warrant this product against defects or malfunctions in materials and workmanship, and against

failure to conform to this product's written specifications, all for one (1) year from the date of original

purchase by you. WE MAKE NO OTHER EXPRESS WARRANTY OR REPRESENTATION OF ANY

KIND WHATSOEVER CONCERNING THIS PRODUCT. Your remedies under this warranty will be

available so long as you can show in a reasonable manner that any defect or malfunction in materials

or workmanship, or any non-conformity with the product's written specifications, occurred within one

year from the date of your original purchase, which must be substantiated by a dated sales receipt or

sales slip. Any such defect, malfunction, or non-conformity which occurs within one year from your

original purchase date will either be repaired without charge or be replaced with a new product iden-

tical or reasonably equivalent to this product, at our option, within a reasonable time after our receipt

of the product. If such defect, malfunction, or non-conformity remains after a reasonable number of

attempts to repair by us, you may elect to obtain without charge a replacement of the product or a

refund for the product. THIS REPAIR, OR REPLACEMENT OR REFUND (AS JUST DESCRIBED)

IS THE EXCLUSIVE REMEDY AVAILABLE TO YOU AGAINST US FOR ANY DEFECT,

MALFUNCTION, OR NON-CONFORMITY CONCERNING THE PRODUCT OR FOR ANY LOSS OR

DAMAGE RESULTING FROM ANY OTHER CAUSE WHATSOEVER. WE WILL NOT UNDER ANY

CIRCUMSTANCES BE LIABLE TO ANYONE FOR ANY SPECIAL, CONSEQUENTIAL,

INCIDENTAL, OR OTHER INDIRECT DAMAGE OF ANY KIND.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the

above limitations or exclusions may not apply to you.
This warranty does NOT apply in the following circumstances: (1) when the product has been serviced

or repaired by anyone other than us; (2) when the product has been connected, installed, combined,

altered, adjusted, or handled in a manner other than according to the instructions furnished with the

product; (3) when any serial number has been effaced, altered, or removed; or (4) when any defect,

problem, loss, or damage has resulted from any accident, misuse, negligence, or carelessness, or from

any failure to provide reasonable and necessary maintenance in accordance with the instructions of

the owner's manual for the product.
We reserve the right to make changes or improvements in our products from time to time without

incurring the obligation to install such improvements or changes on equipment or items previously

manufactured.
This warranty gives you specific legal rights and you may also have other rights which may vary from

state to state.
REMINDER: You must retain the sales slip or sales receipt proving the date of your original purchase

in case warranty service is ever required.

EAGLE ELECTRONICS

PO BOX 669, CATOOSA, OK 74015

(800) 324-1354

Содержание CUDA 350 S/MAP




















































































































































































Результаты поиска

Содержание CUDA 350 S/MAP

Отзывы:

Похожие инструкции для CUDA 350 S/MAP

Бренды по названию

Популярные бренды

Eagle CUDA 350 S/MAP, Инструкция по установке и эксплуатации

Результаты поиска

Содержание CUDA 350 S/MAP

Отзывы:

Похожие инструкции для CUDA 350 S/MAP

Бренды по названию

Популярные бренды