Eagle CUDA 350 S/MAP Скачать руководство пользователя страница 47

Страница: 47 / 180

nector and about 6 inches of cable through the opening under the sonar

mount. Close the cover, plug the connector into the sonar unit and

mount the unit on the built-in bracket.

PPP-12 Portable Power Pack with a sonar unit stowed for transport.

Turn the unit on. If it doesn't work, make sure the battery terminals

are making good contact against the battery contacts. Also check the

wiring connections on the battery adapter. The red wire on the power

cable should be attached to the red wire on the battery adapter and the

power cable's black wire should be connected to the black wire on the

battery adapter.
If it still doesn't work, check the battery voltage. Most of the complaints

we receive about portable units result from stale batteries. Make sure

the ones you buy are fresh.
In cold weather the efficiency of dry cell batteries drops with the tem-

perature. We find it a good idea to have the sonar unit good and warm

along with the batteries before we leave home.

Содержание CUDA 350 S/MAP




















































































































































































Результаты поиска

Содержание CUDA 350 S/MAP

Отзывы:

Похожие инструкции для CUDA 350 S/MAP

Бренды по названию

Популярные бренды

Eagle CUDA 350 S/MAP, Инструкция по установке и эксплуатации

Результаты поиска

Содержание CUDA 350 S/MAP

Отзывы:

Похожие инструкции для CUDA 350 S/MAP

Бренды по названию

Популярные бренды