Eagle CUDA 350 S/MAP Скачать руководство пользователя

Страница: 58 / 180

Sonar Quick Reference

1. Mount the transducer and unit. Connect the unit to electric power

and the transducer.
2. Launch your boat.
3. To turn on the unit, press and release

PWR

key.

4. Head for your fishing area. Your unit automatically displays digital

depth and surface water temperature in the corner of the screen.
5. As you watch the sonar returns, you can change the display by:

Zoom in

to enlarge the chart for more detail: press

ZIN

Zoom out

to return to full chart mode: press

ZOUT

6. If necessary, adjust sensitivity to improve chart readability. Press

MENU

ENT

and the Sensitivity Menu will appear on the left of your

screen. Use

↑

and

↓

to change the setting.

7. Watch the display for the appearance of fish arches. When you see

arches, you have found fish!
8. Gauge the fish depth by visually comparing the fish arches with the

depth scale on the right side of the screen or get a more accurate meas-
ure with the Depth Cursor. Press

MENU

↓

EPTH

URSOR

ENT

. Press

↓

↑

to align the cursor line with the fish arch. The depth appears in a box

at the right end of the cursor line. To clear the cursor, press

EXIT

9. If you are drifting at a very low speed or anchored, you are not mov-

ing fast enough for the unit to return a fish arch signal. As you drift

over a fish or as a fish swims through the transducer's signal cone, the

fish echo will appear as a straight line suspended between the surface

and the bottom.
10. To turn off the unit, press and hold

PWR

key for three seconds.

Содержание CUDA 350 S/MAP




















































































































































































Результаты поиска

Содержание CUDA 350 S/MAP

Отзывы:

Похожие инструкции для CUDA 350 S/MAP

Бренды по названию

Популярные бренды

Eagle CUDA 350 S/MAP, Инструкция по установке и эксплуатации

Результаты поиска

Содержание CUDA 350 S/MAP

Отзывы:

Похожие инструкции для CUDA 350 S/MAP

Бренды по названию

Популярные бренды