Eagle CUDA 350 S/MAP Скачать руководство пользователя страница 105

Страница: 105 / 180

more than 60,000 navigation aids and 10,000 wrecks and obstructions

in U.S. coastal and Great Lakes waters

NOTE:

If you have a Cuda 350i, your unit has medium-detail maps of the

entire world.

The Map Page has its own menu, which is used for several functions

and for setting various options. To access the Map Page Menu, from the

Map Page, press

MENU

The Pages Menu has several display options under the Map Page cate-
gory. Press

PAGES

←

→

↓

to page display option|

EXIT

Map with Sonar Page

This page mode splits the screen in half, with a map on the left and the

sonar chart on the right. This screen option can be found on the Pages

Menu under the Map Page category.

Map with Sonar page (left). Resize Window command selected from

sonar menu (center). Resizing the window (right).

When this screen is activated, you need to specify which side of the Menu is

active. To toggle between the two windows, press

PAGES

. To switch

back, press

PAGES

again.

The following page contains a 12-step quick reference for the most basic

GPS operations.

Содержание CUDA 350 S/MAP




















































































































































































Результаты поиска

Содержание CUDA 350 S/MAP

Отзывы:

Похожие инструкции для CUDA 350 S/MAP

Бренды по названию

Популярные бренды

Eagle CUDA 350 S/MAP, Инструкция по установке и эксплуатации

Результаты поиска

Содержание CUDA 350 S/MAP

Отзывы:

Похожие инструкции для CUDA 350 S/MAP

Бренды по названию

Популярные бренды