Eagle CUDA 350 S/MAP Скачать руководство пользователя

Страница: 125 / 180

117

Delete icons menu.

The Delete All Icons command will ask if you are sure. Press

←

ENT

. All icons will be deleted from the map.

The Delete by Symbol command will launch the Select Symbol menu.
Use

←

↑

→

↓

to select an icon to delete, then press

ENT

. A mes-

sage will appear letting you know all icons with the selected symbol

have been deleted.
The Delete From Map command will prompt you to move the cursor

over an icon to select it. After selecting the icon, press

ENT

and it will

disappear from the map.

Navigate to an Icon

Use the Navigate to Cursor command and the cursor to select the de-

sired icon on the map.
1. Center cursor crosshairs over the icon.
2. To navigate to the selected icon location press

MENU

ENT

EXIT

. Fol-

low course line on the Map Page or the compass bearing arrow on the

Navigation Page.

Содержание CUDA 350 S/MAP




















































































































































































Результаты поиска

Содержание CUDA 350 S/MAP

Отзывы:

Похожие инструкции для CUDA 350 S/MAP

Бренды по названию

Популярные бренды

Eagle CUDA 350 S/MAP, Инструкция по установке и эксплуатации

Результаты поиска

Содержание CUDA 350 S/MAP

Отзывы:

Похожие инструкции для CUDA 350 S/MAP

Бренды по названию

Популярные бренды