Eagle CUDA 350 S/MAP Скачать руководство пользователя страница 46

Страница: 46 / 180

Portable Sonar Installation

Like many Eagle products, the Cuda 350 sonar is capable of portable

operation. It uses the optional PPP-12 portable power pack.
The power pack and portable transducers expand the uses for your so-

nar. You can use your Cuda 350 sonar unit on your boat or take it to

the dock, on a float tube, on an ice fishing trip or use it as a second so-

nar in a friend's boat. (An alternative to the PPP-12 is the PPP-15

portable power pack, which was designed especially for ice fishing. It

includes a rechargeable gel cell battery and a transducer designed for

stationary use. The entire rig is contained in a carry bag that fits inside

a five-gallon plastic bucket.)
The PPP-12 package includes the power pack, battery adapter and a port-

able transducer. The transducer can be stored inside the power pack. The

PPP-12 requires eight AA alkaline batteries. Batteries are not included.
To use a portable power pack, you install the batteries and then attach

the sonar unit to the power pack's bracket. Plug in the

power/transducer cable and you're ready to fish.
The PPP-12 has a quick-release mounting bracket built into the case.

Installing the Batteries

Release the latch on the front of the power pack case. Open the com-

partment and install eight AA batteries into the adapter. For the long-

est life, we recommend you use alkaline batteries.

NOTE:

When the unit is not in use, we recommend you unplug the power

connector to reduce the possibility of corrosion or battery drain.

When you store the unit, always remove the batteries because dead

batteries can leak and corrode the contacts.

After installing the batteries, plug the cable's power connector into the

socket on the battery compartment cover. Route the cable's unit con-

Содержание CUDA 350 S/MAP




















































































































































































Результаты поиска

Содержание CUDA 350 S/MAP

Отзывы:

Похожие инструкции для CUDA 350 S/MAP

Бренды по названию

Популярные бренды

Eagle CUDA 350 S/MAP, Инструкция по установке и эксплуатации

Результаты поиска

Содержание CUDA 350 S/MAP

Отзывы:

Похожие инструкции для CUDA 350 S/MAP

Бренды по названию

Популярные бренды