Eagle CUDA 350 S/MAP Скачать руководство пользователя страница 154

Страница: 154 / 180

146

Pop-up Help

Help is available for most all menu items in this unit. By leaving a

menu item highlighted for a few seconds, a pop-up message appears

that describes its function. This feature is on by default.

To set up Popup Help:

Press

MENU

↓

YSTEM

ETUP

ENT

↓

OPUP

ELP

. With the option highlighted, press

ENT

to turn it on

(check) and turn it off (uncheck). After the option is set, press

EXIT

to return to the main page display.

System Setup Menu (left) with Pop-up Help highlighted. The

Pop-up Help message for the Sensitivity command (right).

Reset Options

To reset all features to factory defaults:

Press

MENU

↓

YSTEM

ETUP

ENT

↓

ESET

PTIONS

ENT

←

ENT

NOTE:

Reset Options does

not

erase any waypoints, routes, icons, plot trails

or sonar logs.

Содержание CUDA 350 S/MAP




















































































































































































Результаты поиска

Содержание CUDA 350 S/MAP

Отзывы:

Похожие инструкции для CUDA 350 S/MAP

Бренды по названию

Популярные бренды

Eagle CUDA 350 S/MAP, Инструкция по установке и эксплуатации

Результаты поиска

Содержание CUDA 350 S/MAP

Отзывы:

Похожие инструкции для CUDA 350 S/MAP

Бренды по названию

Популярные бренды