E-Z-GO FREEDOM, Руководство владельца и по обслуживанию

Страница: 26 / 158

OPERATION AND SERVICE INFORMATION
Page 6
Owner’s Manual and Service Guide
Read all of manual to become thoroughly familiar with this vehicle. Pay particular attention to all Notes, Cautions and Warnings
Clean windshield with lots of water and a clean cloth. Minor
scratches may be removed using a commercial plastic
polish or Plexus
®
plastic cleaner available from the service
parts department.
Normal cleaning of vinyl seats and plastic or rubber trim
requires the use of a mild soap solution applied with a
sponge or soft brush and wipe with a damp cloth.
Removal of oil, tar, asphalt, shoe polish, etc. will require the
use of a commercially available vinyl/rubber cleaner.
The painted surfaces of the vehicle provide attractive
appearance and durable protection. Frequent washing with
lukewarm or cold water and mild detergent is required to
preserve the painted surfaces.
Occasional cleaning and waxing with non-abrasive products
designed for ‘clear coat’ automotive finishes will enhance
the appearance and durability of the painted surfaces.
Corrosive materials used as fertilizers or for dust control can
collect on the underbody of the vehicle. These materials will
cause corrosion of underbody parts unless flushed
occasionally with plain water. Thoroughly clean any areas
where mud or other debris can collect. Sediment packed in
closed areas should be loosened to ease it’s removal, taking
care not to chip or otherwise damage paint.
If the engine does not start or runs improperly
after washing, remove the spark plug wires (by
pulling the spark plug boots, never the wires). Dry all
connections with forced air. Reinstall the wires.
VEHICLE CARE PRODUCTS
To help maintain the vehicle there are several products
available through local Distributors, authorized Branches, or
the Service Parts Department.
•
Touch-up paint specially formulated to match vehicle
colors for use on both metal and molded plastic
bodies. (P/N 28140-G** and 28432-G**)
•
Battery Protectant formulated to form a long-term,
flexible, non-tacky, dry coating that will not crack,
peel or flake over a wide temperature range. (P/N
75500-G01)
•
White Lithium Grease designed to provide lubrication
protection in areas where staining or discoloring is a
problem, or in areas of extreme temperature ranges.
(P/N 75502-G01)
•
Penetrant/Lubricant, a 4-in-1 product that penetrates
seized parts, lubricates leaving a light lubricating
film, reduces corrosion by adhering to wet or dry
surfaces and displaces moisture, sealing against
future moisture return. (P/N 75503-G01)
•
Multi-purpose Cleaner and Degreaser that contains
natural, environmentally safe solvents. (P/N 75504-
G01)
•
Multi-purpose Hand Cleaner is an industrial strength
cleaner containing no harsh solvents, yet gently lifts
grease off hands. May be used with or without water.
(P/N 75505-G01)
•
Battery Cleaner that neutralizes battery acids and
dissolves terminal corrosion and can be rinsed with
water. (P/N 75506-G01)
•
Biodegradable Cleaner that breaks down grease to
be easily wiped or rinsed away. (P/N 75507-G01)
•
Multi-purpose Value Pack sampler includes 4 ounce
(118 ml) aerosol cans of Battery Protector,
Penetrant/Lubricant, White Lithium Grease, and
Carburetor and Choke Cleaner. (P/N 75508-G01)
•
Plexus
®
plastic cleaner and polish removes minor
scratches from windshield. (P/N 28433-G**)
REPAIR
LIFTING THE VEHICLE
Tool List Qty. Required
Floor jack ......................................................................... 1
Jack stands ...................................................................... 4
Chocks ............................................................................. 4
Some servicing operations may require the front wheels, the
rear wheels, or the entire vehicle be raised.
To reduce the possibility of
severe injury or death from
a vehicle falling from a
jack:
Be sure the vehicle is on a firm and level surface.
Never get under a vehicle while it is supported by a
jack.
Use jack stands and test the stability of the vehicle on
the stands.
Always place chocks in front and behind the wheels
not being raised.
Use extreme care since the vehicle is extremely
unstable during the lifting process.
When lifting vehicle, position jacks and
jack stands at the areas indicated only.
To raise the entire vehicle, install chocks in front and behind
each front wheel (Ref. Fig. 9 on page 7). Center the jack
under the rear frame crossmember. Raise the vehicle
enough to place a jack stand under the outer ends of the
rear axle.
Lower the jack and test the stability of the vehicle on the two
jack stands.
! !