manualshive.com logo in svg

E-FLITE Blade CP Pro, Инструкция по эксплуатации

Инструкция к E-FLITE Blade CP Pro доступна для скачивания бесплатно на нашем сайте. Руководство поможет вам быстро ознакомиться с устройством и его особенностями. Скачайте руководство на manualshive.com прямо сейчас, чтобы насладиться полноценным использованием этого продукта.

Поделиться
Скачать
background image

1

•. If.this.is.the.first.test.flight,.or.a.test.flight.following.repairs,.you.will.also.want.to.center.the.rudder,.aileron..

and.elevator.trims .

•. Once.confirming.the.transmitter.has.been.turned.on.and.has.an.adequate.level.of.battery.power.as.displayed.by.

the.LEDs.at.the.top.of.the.transmitter,.it.is.now.safe.to.plug.the.flight.battery.to.the.3-in-1.unit .

•. With battery power applied, the -in-1 unit status LED will blink red, then blink green. It is extremely 

important that during this time of calibration the helicopter is not moved or swayed in order for the 
gyro to properly initialize. If.the.helicopter.was.moved.or.swayed.during.this.time,.unplug.the.flight.battery.
and.repeat.the.initialization.process .

•. When.the.status.LED.becomes.solid.green,.the.unit.is.armed.and.ready.for.flight ..Use.caution.as.both.the.main.

and.tail.rotors.will.now.run.with.throttle.stick.input ..For.safety,.once.the.unit.is.armed,.the.main.and.tail.motors.
will.not.run.with.the.throttle.stick.and.trim.in.their.lowest.positions ..Do.not.advance.the.throttle.stick.until.you.
are.clear.of.the.rotor.blades.and.ready.to.fly .

Note: If the status LED does not become solid green, please review the following:

•. If.after.blinking.red.the.status.LED.becomes.solid.red,.you.have.a.positive.Radio.Frequency.(RF).link.between.

the.transmitter.and.receiver/3-in-1.unit,.but.the.throttle.stick.and.throttle.trim.may.not.be.in.their.lowest.possible.
positions ..Check.to.be.sure.that.both.the.throttle.stick.and.throttle.trim.are.in.their.lowest.possible.position.and.
the.status.LED.should.blink.green.then.become.solid.green.indicating.the.unit.is.armed.and.ready.for.flight ..
Proceed.to.the.next.step.of.the.checklist.once.the.unit.is.armed .

•. If.after.blinking.red.the.status.LED.continues.to.flash.from.green.to.red,.you.do.not.have.a.positive.RF.link.

between.the.transmitter.and.receiver/3-in-1.unit ..First,.check.to.be.sure.that.the.transmitter.has.been.powered.
on.and.has.an.adequate.level.of.battery.power ..If.the.transmitter.was.indeed.powered.on,.power.both.the.
transmitter.and.3-in-1.unit.down,.then.check.that.the.crystal.in.the.transmitter.and.the.crystal.in.the.receiver..

are.properly.seated.and.secured.in.their.mounts ..Once.you.have.confirmed.the.crystals.are.properly.seated..
and.secured,.turn.on.the.transmitter.and.then.connect.the.flight.battery.to.the.3-in-1.unit ..The.3-in-1.unit.should.
now.arm.normally .

If.your.3-in-1.unit.will.not.arm.after.following.the.guidelines.as.listed.above,.contact.Horizon.Hobby’s.Product.
Support.staff.at.1-877-504-0233 .

•. Once.you.have.placed.the.helicopter.in.a.safe.place.to.fly,.free.of.obstructions,.and.are.clear.of.the.rotor.

blades,.you.can.safely.power.up.the.model .

Note: If this is your first test flight, the model should not be flown indoors unless it is in a very large 

area such as a gym. Until you have properly trimmed, adjusted and become familiar with the handling 

of the Blade™ CP Pro, we suggest your first and any subsequent test flights be made outdoors in 

calm air only.

•. Advance.the.throttle.stick.slowly,.just.until.both.the.main.and.tail.rotor.blades.begin.to.spin ..Note.the.direction.

that.the.main.and.tail.rotor.blades.spin ..The.main.rotor.blades.should.spin.clockwise.when.viewed.from.the.
top,.with.the.tail.rotor.blade.spinning.counterclockwise.when.viewed.from.the.right-hand.side.of.the.helicopter ..
If.either.set.of.rotor.blades.is.operating.in.the.wrong.direction,.unplug.the.battery,.and.then.simply.reverse.its.
motor.wire.plug.polarity.on.the.3-in-1.unit .

Содержание Blade CP Pro

































































Отзывы:

Нет отзывов

Похожие инструкции для Blade CP Pro

Harbor Freight Tools 94840 Set Up And Operating Instructions Manual preview
94840
Бренд: Harbor Freight Tools Страницы: 7
Parkside PP 1500 A1 Operation And Safety Notes, Notes For Parents preview
PP 1500 A1
Бренд: Parkside Страницы: 40
iKarus BELL UH-1D Mounting Instructions preview
BELL UH-1D
Бренд: iKarus Страницы: 15
Walkera HM 4G1A User Handbook Manual preview
HM 4G1A
Бренд: Walkera Страницы: 10
PREZIOSI KOKUYO Flair Klixi Mixi Manual preview
KOKUYO Flair Klixi Mixi
Бренд: PREZIOSI Страницы: 6
V-tech 80-551703 Instruction Manual preview
80-551703
Бренд: V-tech Страницы: 14
VTech Winnie The Pooh Play n Learn Spinning Top User Manual preview
Winnie The Pooh Play n Learn Spinning Top
Бренд: VTech Страницы: 10
Faller Compessor with drive Quick Start Manual preview
Compessor with drive
Бренд: Faller Страницы: 4
Fisher-Price LittlePeople K0104 Instruction Sheet preview
LittlePeople K0104
Бренд: Fisher-Price Страницы: 12
Wings Maker SZD-45 OGAR Instruction Manual preview
SZD-45 OGAR
Бренд: Wings Maker Страницы: 12
Bengtson Company Supermarine Sparrow I 36 Instructions preview
Supermarine Sparrow I 36
Бренд: Bengtson Company Страницы: 5
Rail King Premier BL-2 Diesel Engine Operator'S Manual preview
Premier BL-2 Diesel Engine
Бренд: Rail King Страницы: 28
E sky belt-cp Instruction Manual preview
belt-cp
Бренд: E sky Страницы: 43
Radio control model L-19/0-1 BIRD DOG 1730mm Wingspan Instruction Manual preview
L-19/0-1 BIRD DOG 1730mm Wingspan
Бренд: Radio control model Страницы: 32
Skymaster ARF F-18E Instruction Manual preview
ARF F-18E
Бренд: Skymaster Страницы: 14
Reely Sky 20 70 10 Operating Instructions Manual preview
20 70 10
Бренд: Reely Sky Страницы: 108
VTech Alphabet Soup User Manual preview
Alphabet Soup
Бренд: VTech Страницы: 10
Bresser National Geographic Astro Planetarium Multimedia Operating Instructions Manual preview
National Geographic Astro Planetarium Multimedia
Бренд: Bresser Страницы: 48

Бренды по названию

Популярные бренды

Загрузить еще бренды