manualshive.com logo in svg

E-FLITE Blade CP Pro, Инструкция по эксплуатации

Поделиться
Скачать
E-FLITE Blade CP Pro Скачать руководство пользователя страница 29

9

Note: The ESC in the -in-1 used to control the main motor has been calibrated for a narrower  

range of throttle operation. For this reason, it will not be necessary to set the Idle Up TCM ADJ  

knob much beyond approximately 1/ travel in order to achieve 100% throttle at mid stick. This is  

not a problem and there is no adverse affect for having the knob adjusted to beyond approximately  

1/ travel, though it is not necessary. The status LED indicator on the -in-1 will turn solid red when  

full power has been achieved.

When.using.the.optional,.370.brushless.power.system.(as.seen.in.the.“Optional.Brushless.Main.Motor.Power.
System.Installation.and.Setup”.section.found.on.pages.48–56),.we.recommend.adjusting.the.Idle.Up.TCM.ADJ.
knob.to.provide.the.best.overall.combination.of.main.rotor.head.speed.and.collective/cyclic.response.depending.
on.your.preferred.style.of.flying,.similar.to.as.noted.for.the.stock.bushed.370.power.system ..However,.please.
note.that.while.it.is.possible.to.fly.with.the.midpoint.set.to.approximately.100%.throttle.when.using.the.optional.
brushless.power.system,.care.must.be.taken.during.flight.to.prevent.over.speeding.of.the.main.rotor.blades,.
especially.during.fast.descents .

Note: Some brushless ESCs may also be calibrated with a narrower range of throttle operation 

and could achieve 100% throttle before the Idle Up TCM ADJ knob reaches full travel. This is not a 

problem and should have no adverse affect on flight performance.

Please.see.the.“Programmed.Throttle.and.Pitch.Curves.for.the.Idle.Up/Stunt.Flight.Mode”.section.found.on.pages.
31–32.for.more.information.regarding.adjustment.of.the.Idle.Up.TCM.ADJ.knob .

Содержание Blade CP Pro

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды