manualshive.com logo in svg

E-FLITE Blade CP Pro, Инструкция по эксплуатации

Поделиться
Скачать
E-FLITE Blade CP Pro Скачать руководство пользователя страница 49

9

The.following.steps.outline.installation.and.setup.of.the.recommended.optional.brushless.power.system:

•. In.order.to.provide.the.most.secure.motor.mounting,.and.proper.clearance.for.the.forward.bearing.cup.in.the.

main.frame,.it.will.be.necessary.to.install.the.Park.370.brushless.motor’s.(EFLM1000).included.“Adapter.Ring .”

•. After.installing.the.adapter.ring,.it.will.then.be.necessary.to.remove.the.stock.brushed.main.motor.from.the.

main.frame.in.order.to.trial.fit.the.brushless.motor.to.check.for.proper.placement.of.the.pinion.on.the.brushless.
motor’s.shaft .

Note:.Before.removing.the.stock.brushed.main.motor,.we.suggest.that.you.check.the.gear.mesh.of.its.9-tooth.

pinion.and.the.main.drive.gear,.in.multiple.places.on.the.main.drive.gear,.for.reference ..This.is.approximately.how.

you.will.want.to.set.the.pinion.and.main.gear.mesh.after.installing.the.brushless.motor.and.the.8-tooth.pinion .

•. Once.the.stock.brushed.main.motor.has.been.removed.from.the.frame,.temporarily.install.the.Park.370.

brushless.motor ..Then,.using.the.8-Tooth.Pinion.Gear.(EFLM1949).and.main.gear.for.reference,.mark.the.shaft.
of.the.motor.(using.a.marker.or.tape).at.the.point.to.which.the.pinion.gear.should.be.press.fit.onto.the.shaft.
to.provide.adequate.gear.tooth.contact.of.the.pinion.and.main.gear ..It.is.important.to.install.the.pinion.on.the.
motor.shaft.so.that.it.will.always.offer.full.contact.with.the.main.gear.teeth.in.order.to.promote.the.best.power.
transfer.and.to.prevent.uneven.and/or.accelerated.gear.wear .

Содержание Blade CP Pro

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды