E-FLITE Blade CP Pro Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 64

background image

•. Next,.power.on.the.transmitter,.then.the.plug.the.battery.pack.into.the.battery.lead.of.the.3-in-1.control.unit ..

Allow.time.for.the.3-in-1.control.unit.to.initialize.properly ..Also,.be.sure.to.allow.the.gyro.to.initialize.properly,.
as.outlined.in.its.manual ..If.you.are.using.the.G90.gyro,.the.blue.status.LED.should.illuminate.solidly.just.before.
the.status.LED.of.the.3-in-1.unit.becomes.solid.green ..This.will.indicate.that.the.gyro.and.3-in-1.control.unit.are.
ready.for.the.test .

•. After.securing.the.helicopter.and.ensuring.that.all.objects.are.free.and.clear.of.the.tail.rotor.blades,.and.also.

reconfirming.that.the.main.motor.power.lead.has.been.disconnected.from.the.3-in-1.control.unit,.advance.the.
throttle/collective.stick.on.the.transmitter.to.approximately.1/3–1/2.travel ..Use.caution,.as.the.tail.motor.may.
begin.to.spin.the.tail.rotor.blade .

•. Now.it.is.best.to.check.that.the.tail.motor/rotor.is.responding.properly.to.transmitter.inputs ..When.inputting.

a.slight.amount.of.right.rudder,.the.tail.rotor.rpms.should.increase.(to.push.the.nose.of.the.helicopter.to.the.
right) ..When.inputting.a.slight.amount.of.left.rudder,.the.tail.rotor.rpms.should.decrease.or.stop.entirely ..If.
the.tail.motor/rotor.is.not.responding.properly,.use.the.Servo.Reversing.switch.located.on.the.front.of.the.
transmitter.to.reverse.the.direction.of.response .

•. Once.confirming.that.the.tail.motor/rotor.is.responding.properly.to.transmitter.inputs,.it.will.also.be.necessary.

to.confirm.that.it.is.responding.properly.to.inputs.from.the.gyro ..After.again.securing.the.helicopter.and.
ensuring.that.all.objects.are.free.and.clear.from.the.tail.motor,.and.that.the.throttle.is.set.to.approximately.
1/3–1/2.power,.quickly.twist.the.nose.of.the.helicopter.to.the.left ..If.the.tail.motor/rotor.is.responding.properly.
to.inputs.from.the.gyro,.the.rpms.will.increase,.to.counteract.the.nose.twisting.to.the.left,.in.order.to.bring.the.
nose.back.to.the.right ..When.quickly.twisting.the.nose.of.the.helicopter.to.right,.the.rpms.should.decrease.or.
stop.entirely ..If.the.tail.motor/rotor.is.not.responding.properly,.use.the.Reverse.switch.located.on.the.gyro.to.
reverse.the.direction.of.response .

•. After.confirming.that.the.tail.motor/rotor.is.responding.properly.to.inputs.from.the.gyro.and.transmitter,.

disconnect.the.battery.from.the.3-in-1.control.unit,.power.down.the.transmitter.and.re-install.the.main.motor.
power.lead.into.the.3-in-1.noting.proper.polarity.for.correct.operation .

«
...
42
43
44
45
46
...
»

Содержание Blade CP Pro

































































Отзывы:

Нет отзывов

Похожие инструкции для Blade CP Pro

SET OF FUNFAIR CARAVANS II

Бренд: Faller Страницы: 4

HALF-TIMBERED HOUSE

Бренд: Faller Страницы: 4

Бренд: Faller Страницы: 4

KID Trax KT1555WM

Бренд: PACIFIC CYCLE Страницы: 20

Бренд: H-KING Страницы: 15

Бренд: Black Horse Model Страницы: 20

Бренд: Fisher-Price Страницы: 2

Midwest FreightReady-to-Run Set

Бренд: Lionel Страницы: 16

Бренд: Idena Страницы: 3

Бренд: Faller Страницы: 12

INTERACTIVE NODDY CAR

Бренд: LEXIBOOK Страницы: 33

Бренд: BLOTZ Страницы: 2

Pike Perfection-Cross tail

Бренд: Samba Страницы: 3

Бренд: Hot Wheels Страницы: 2

Бренд: Eduard Страницы: 4

Бренд: Little Tikes Страницы: 2

Бренд: PARKZONE Страницы: 10

Spitfire F.Mk.22/24 landing flaps

Бренд: Eduard Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды