manualshive.com logo in svg

E-FLITE Blade CP Pro, Инструкция по эксплуатации

Поделиться
Скачать
E-FLITE Blade CP Pro Скачать руководство пользователя страница 40

0

Optional Heading Lock Gyro Installation and Setup

A.unique.feature.of.the.Blade™.CP.Pro.is.that.it.allows.you.to.install.an.optional.“Heading.Lock”.type.gyro.to.
further.enhance.the.holding.performance.and.response.of.the.tail,.without.the.need.for.difficult.modifications.or.an.
alternative.radio.system ..While.the.stock.“Standard.Rate”.type.gyro.contained.in.the.3-in-1.control.unit.performs.
well.for.many.types.of.flying,.a.heading.lock.gyro.offers.superior.tail.holding.power.that.helps.to.maintain.heading.
throughout.even.the.most.aggressive.aerobatic.maneuvers .

When.installing.a.heading.lock.type.gyro,.we.recommend.the.E-flite

®

.G90.Sub-Micro.Heading.Lock.gyro.

(EFLRG90HL) ..The.G90.gyro.weighs.only.9 .0.grams.( .32.oz),.and.features.a.very.small.footprint.that.makes.
mounting.it.on.the.gyro.mounting.plate.quick.and.easy ..It.also.offers.the.ability.to.control.the.gain.setting.(in.either.
Standard.Rate.or.Heading.Lock.modes).remotely.from.the.Blade.CP.Pro’s.included.transmitter.by.using.the.5th.
channel,.and.is.an.excellent.choice.when.looking.for.the.best.in.tail.and.heading.lock.performance .

Note: The following steps outline the installation and setup of the G90 gyro, but can also be used as 

reference for many other heading lock type gyros. However, we do recommend that you review the 

manual included with your chosen gyro first before proceeding with installation and setup of the gyro 

in your Blade CP Pro.

•. Install.the.gyro.using.its.included.foam.mounting.tape.(or.the.foam.mounting.tape.found.in.the.Blade.CP.Pro’s.

included.“Mounting.Accessories.&.Wrench”.package).on.the.gyro.mounting.plate.found.just.behind.the.rear.
servos ..Be.sure.to.orient.the.gyro.so.that.you.can.easily.access.the.gain.setting.adjustment.pot.(if.not.using.the.
remote.gain.setting.control.option).and.any.necessary.reversing.or.other.setting.switches .

Содержание Blade CP Pro

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды