E-FLITE Blade CP Pro Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 64

background image

Main Rotor Blade Tracking Adjustment

Caution: Be sure to maintain a safe distance from the helicopter (10–1 feet) when tracking the main

rotor blades.

Blade.tracking.is.a.critical.element.to.the.flight.performance.of.just.about.any.helicopter,.including.the.Blade™.CP.
Pro ..Main.rotor.blades.that.are.out.of.track.may.cause.vibration,.instability,.and.loss.of.power.due.to.increased.
drag ..Although.each.Blade.CP.Pro.model.is.test.flown.with.blades.tracked.at.the.factory,.minor.adjustments.to.
blade.tracking.may.be.required.after.blade.changes,.repairs,.or.pitch.curve.adjustments .

For.checking.main.rotor.blade.tracking.and.making.adjustments,.please.read.the.following.tips:

• Before proceeding with the test flight of a new model, or any model to which changes or repairs

have been made, be certain that the main rotor blades have been properly installed and secured.
The main blades should be tightened so they can pivot in the blade grip when moderate pressure is
applied. Never allow the main blades to swing freely in their grips.

•. Following.the.proper.initialization.and.arming.procedure.previously.outlined.in.the.“3-in-1.Control.Unit.Description,.

Arming.and.Adjustment”.section,.bring.the.main.rotor.blades.of.your.Blade.CP.Pro.up.to.speed ..You.can.check.
the.blade.tracking.either.on.the.ground.or.in.the.air.at.eye.level ..It.might.be.a.good.idea.to.have.an.assistant.
on.hand.to.help.sight.the.blades ..Again, be certain to maintain a safe distance of 10–1 feet from the
helicopter when checking the tracking of the main rotor blades.

•. Once.the.main.rotor.blades.have.been.brought.up.to.speed,.note.which.blade.is.running.low.and.which.blade.is.

running.high.(by.the.colored.tracking.tape) .

•. You.can.then.power.the.helicopter.down.and.increase.the.pitch.of.the.low.blade.by.turning.its.Pitch.Control.Link.

end.out.one.half.to.one-full.turn.at.a.time ..Or,.you.can.decrease.the.pitch.of.the.high.blade.by.turning.its.Pitch.
Control.Link.end.in.one-half.to.one.full.turn.at.a.time .

«
...
31
32
33
34
35
...
»

Содержание Blade CP Pro

































































Отзывы:

Нет отзывов

Похожие инструкции для Blade CP Pro

Little white rocker

Бренд: Bandits and Angels Страницы: 5

Бренд: Tough Jets Страницы: 22

Бренд: Faller Страницы: 12

Бренд: Horizon Hobby Страницы: 19

Бренд: marklin Страницы: 32

Бренд: Top R/C Hobby Страницы: 13

Бренд: VA Models Страницы: 8

Бренд: Top Flite Страницы: 36

Бренд: BigPlanes Страницы: 9

Habu 32 EDF ARF

Бренд: E-FLITE Страницы: 108

Toot-Toot Drivers Press ‘n’ Go Vehicle

Бренд: VTech Страницы: 3

Бренд: Faller Страницы: 12

Nick Jr The Backyardigans L2176

Бренд: Fisher-Price Страницы: 20

73510 Volkswagen New Beetle

Бренд: Power Wheels Страницы: 36

BUILDING SITE DECORATION

Бренд: Faller Страницы: 4

Бренд: LeapFrog Страницы: 13

330X Quad-Flyer

Бренд: GAUI Страницы: 24

A-26B Undercarriage & exterior

Бренд: Eduard Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды