E-FLITE Blade CP Pro Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 64

background image

When.the.“Idle.Up”.switch.is.toggled.toward.the.rear.of.the.transmitter,.the.Blade™.CP.Pro.will.be.flying.in.“Normal.
Mode .”.In.this.flight.mode,.the.throttle.curve.is.linear.from.0%.to.100%,.with.a.pitch.range.of.approximately.-1.
degree.to.+12.degrees ..(See.page.31.for.additional.data.and.graphics.relating.to.the.throttle.and.pitch.curves.
preset.for.your.Blade.CP.Pro .).This.is.the.preferred.flight.mode.for.general.hovering.and.gentle.forward.flight .

When.the.“Idle.Up”.switch.is.toggled.toward.the.front.of.the.transmitter,.the.Blade.CP.Pro.will.be.flying.in.the.
“Stunt.(aerobatic)”.flight.mode ..In.this.flight.mode,.the.throttle.curve.will.be.“V”.or.“Flat-Line”.shaped.from.100%.to.
100%.with.approximately.50%.to.100%.throttle.at.mid-stick.(the.mid-stick.throttle.percentage.value.will.depend.on.
where.the.“Idle.Up.Throttle.Curve.Midpoint.Adjustment”.knob.is.set,.as.outlined.on.pages.27–29) ..The.pitch.range.
will.then.be.approximately.-12.to.+12.degrees.(See.pages.31–32.for.additional.data.and.graphics.relating.to.the.
throttle.and.pitch.curves.pre-set.for.your.Blade.CP.Pro) ..This.flight.mode.is.preferred.for.aggressive.forward.flight.
and.aerobatics,.as.well.as.inverted.flying .

Note: When in the Idle Up/Stunt flight mode, even with the throttle stick all the way down, the blades

and motors will continue to spin. You must use the Normal flight mode to safely turn off the motors.

For safety, the -in-1 unit will not arm if the flight battery is plugged in and the flight mode switch is in

the Idle Up/Stunt position.

When.switching.between.Normal.and.Idle.Up/Stunt.flight.modes,.it.is.best.to.do.so.in.the.air.while.hovering ..The.
throttle.and.pitch.curves.of.each.flight.mode.have.been.optimized.to.transition.smoothly.around.hover ..Please.be.
sure.to.never.switch.into.the.Idle.Up/Stunt.mode.without.having.powered.the.main.and.tail.motors.up.in.Normal.
mode.first ..The.abrupt.start.could.cause.damage.to.the.gears,.motors.or.possibly.even.the.3-in-1.unit .

«
...
24
25
26
27
28
...
»

Содержание Blade CP Pro

































































Отзывы:

Нет отзывов

Похожие инструкции для Blade CP Pro

NIEUPORT 28 ARF

Бренд: Maxford USA Страницы: 16

ZOOM Do 217J-1/2

Бренд: Eduard Страницы: 4

Бренд: Eduard Страницы: 4

Midwest FreightReady-to-Run Set

Бренд: Lionel Страницы: 16

Portable Pit Stop Ramp

Бренд: Race Ramps Страницы: 6

Бренд: Volvo Страницы: 10

Бренд: Zeller Страницы: 14

Бренд: Trix Страницы: 12

Бренд: KDS Страницы: 26

Lego 10283 LIGHT KIT

Бренд: LIGHT MY BRICKS Страницы: 47

Laugh & Learn Puppy's Learning Car

Бренд: Fisher-Price Страницы: 4

60cc Freestyle 260 ARF QB-L

Бренд: AeroWorks Страницы: 75

Бренд: Simplay3 Страницы: 3

IMAGINE SUPER VALUE TUB

Бренд: K'Nex Страницы: 28

Бренд: Beyblade Страницы: 2

Бренд: bewello Страницы: 12

Jimu Robot JR1601

Бренд: UBTECH Страницы: 5

Бренд: Chad Valley Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды