E-FLITE Blade CP Pro Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 64

background image

When.the.Channel.5.knob.is.rotated.clockwise.(+).from.the.middle.position,.the.gyro.will.be.in.the.Heading.
Lock.mode ..This.is.the.mode.that.is.preferred.for.use.after.installing.the.heading.lock.type.gyro ..When.the.
knob.is.rotated.full.clockwise,.the.gain.setting.value.will.be.approximately.100% ..Other.gain.setting.values.
from.approximately.0–100%.are.also.available.depending.on.where.the.knob.is.set.between.the.middle.and.full.
clockwise.positions .

We.recommend.that.you.set.the.Channel.5.knob.in.the.position.that.provides.a.gain.setting.value.of.approximately.
50%.in.the.Heading.Lock.mode.before.conducting.the.first.test.flight.after.installing.the.gyro ..You.will.then.use.the.
Channel.5.knob.on.the.transmitter.for.adjusting.the.gyro.gain.value.after.conducting.test.flights .

Note: It is important that you do not accidentally change the position of the Channel knob between

and during flights once you have found the gain setting value that provides the best tail/heading lock

performance.

•. Once.you.have.made.initial.adjustments.of.the.gyro.gain.setting,.you.will.be.ready.to.conduct.the.first.test.flight.

using.your.new.gyro ..After.making.the.initial.test.flight,.take.your.time.adjusting.the.gyro.gain.setting.value.prior.
to.subsequent.test.flights.in.order.to.find.the.best.possible.performance ..The.goal,.when.using.a.Heading.Lock.
type.gyro,.is.to.find.the.highest.gain.setting.value.at.which.the.tail.of.the.helicopter.will.not.twitch.quickly.from.
side.to.side.in.all.areas.of.flight.(including.fast.forward.flight.and.descents) ..

Note: Although you should now be using a Heading Lock type gyro to help better maintain tail and

heading lock performance during flight, it may be necessary to make small adjustments to the rudder

trim setting on the transmitter in order to prevent “drifting” of the nose/tail of the helicopter. The

amount of trimming required may vary depending on the gyro used and flying conditions.

Now.that.you.have.properly.installed.and.configured.a.heading.lock.gyro.on.your.Blade™.CP.Pro,.you.will.note.a.
significant.improvement.in.the.ability.for.the.tail.motor.power.system.to.maintain.heading.and.position.throughout.
all.areas.of.flight ..Do.note,.however,.that.the.tail.motor.power.system.does.still.have.some.limitations.in.its.
performance.envelope.and.that.you.should.take.your.time.when.learning.these.limits ..In.general,.these.limitations.
do.not.impact.the.majority.of.maneuvers.the.Blade.CP.Pro.is.capable.of,.and.you.will.find.the.performance.of.the.
tail.motor.power.system,.when.combined.with.the.heading.lock.gyro,.is.very.good.overall .

«
...
45
46
47
48
49
...
»

Содержание Blade CP Pro

































































Отзывы:

Нет отзывов

Похожие инструкции для Blade CP Pro

Бренд: Eclipse Страницы: 16

Бренд: Eachine Страницы: 8

Бренд: marklin Страницы: 36

Бренд: LEGO Страницы: 44

Бренд: Tronhelicopters Страницы: 43

Бренд: HobbyBoss Страницы: 8

Бренд: LCUT Creative Страницы: 2

Fauvel AV-361 RC glider

Бренд: Aeronaut Страницы: 5

Бренд: VTech Страницы: 9

Бренд: Spin Master Страницы: 20

MAJO GARAGE MOTOR CITY

Бренд: Smoby Страницы: 7

Бренд: WARCRADLE SCENICS Страницы: 35

SCOOBY-DOO 75901

Бренд: LEGO Страницы: 67

Бренд: Zhejiang Jiajia Ride-On Co. Страницы: 27

Бренд: 4-Max Страницы: 8

Бренд: K'Nex Education Страницы: 24

Бренд: THUNDER TIGER Страницы: 52

Бренд: Multiplex Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды