E-FLITE Blade CP Pro Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 64

background image

If,.after.the.first.few.flights,.you.would.prefer.to.have.even.quicker.and.more.aggressive.cyclic.response,.you.can.
reposition.the.flybar.weights.so.that.they.are.closer.in.to.the.head/main.shaft.on.the.flybar ..It.is.usually.best.to.
move.the.weights.in.only.a.small.distance.at.a.time.before.making.each.subsequent.test.flight,.until.you.find.the.
position.at.which.you.prefer.the.cyclic.response.most .

Note: It is important that the weight(s) on each side of the flybar be positioned at a distance equal

from the head/main shaft in order to prevent imbalance that could lead to vibration in the rotor head.

Dampening.of.the.rotor.head.(main.rotor.blades).can.also.be.adjusted.in.order.to.fine-tune.the.cyclic.response.of.
your.model ..In.general,.stiffer.dampening.will.result.in.quicker.cyclic.response ..The.dampening.of.your.Blade™.CP.
Pro.has.been.set.to.provide.a.good.balance.of.cyclic.response.and.stability.right.out.of.the.box,.and.we.suggest.
that.you.make.your.first.flights.with.this.amount.of.dampening.before.making.any.changes .

If,.after.the.first.few.flights,.you.would.prefer.to.have.even.quicker.and.more.aggressive.cyclic.response,.you.can.
stiffen.the.rotor.head.dampening.by.adding.shims.between.the.O-Ring.and.Step.Washer.on.each.side.of.the.Center.
Hub.(See.the.“Exploded.View”.drawing.and.parts.listing.on.pages.60–61.for.reference) ..Head.Dampening.Shims.
are.available.separately.in.packs.of.eight.(EFLH1144),.however,.you.should.install.only.one.shim.per.side.at.a.time.
before.making.each.subsequent.test.flight,.until.you.find.the.dampening.at.which.you.prefer.the.cyclic.response.
(and.stability).most .

Note: You must always install an equal number of shims on each side of the center hub.

Note: If you install too many shims, and the dampening becomes too stiff, the helicopter can wobble

and shake in flight. Take care when making testing flights after adding shims to prevent crashing

the model as a result of a wobble or shake. Typically, we find that using 1– shims per side with the

stock 0 brushed main motor power system works well. More shims per side can cause the wobble

and shake. If running a power system that is capable of producing higher rotor head speeds, like the

optional 0 brushless power system, you can sometimes add even more shims before encountering

the wobble and shake. Again, exercise extreme care when test flying the model after adding shims.

«
...
35
36
37
38
39
...
»

Содержание Blade CP Pro

































































Отзывы:

Нет отзывов

Похожие инструкции для Blade CP Pro

Бренд: Barbie Страницы: 12

BEASTS ALIVE STOMPZ

Бренд: K'Nex Страницы: 20

P-47-25 interior S.A.

Бренд: Eduard Страницы: 3

Бренд: Step2 Страницы: 12

Steaman Aerobatic Biplane

Бренд: REVELL Страницы: 12

Бренд: Meccano Страницы: 40

Monogram The Gold Knight Of Nice

Бренд: REVELL Страницы: 8

KID K’NEX 123 SEASAME STREET Ernie Building Set 85503

Бренд: K'Nex Страницы: 2

P47 Thunderbolt

Бренд: Black Horse Model Страницы: 30

Бренд: REVELL Страницы: 16

SPRAY INTELLIGENT DINOSAUR FK501B

Бренд: Fei lun Страницы: 8

Бренд: Eduard Страницы: 6

Despicable Me 2 20 112 0005

Бренд: DICKIE TOYS Страницы: 16

Street Vendor Cart

Бренд: The Land of Nod Страницы: 5

Switch & Go Dinos Seeker the T-Rex

Бренд: VTech Страницы: 11

RAILKING GALLOPING GOOSE

Бренд: Rail King Страницы: 32

Havoc Turbo Blast

Бренд: Air Hogs Страницы: 4

Chocolate Sprinkle Stix

Бренд: John Adams Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды