Dynamic Engineering PCIeBiSerialDb37-BA22 Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 44

background image

Embedded Solutions

Page 31

Notes:

1. Writing a zero to this port will abort a write DMA in progress.
2. End of chain should not be set for the address written to the DMA Pointer

Address Register. End of chain should be set when the descriptor follows the
last length parameter.

3. The Direction should be set to ‘1’ for Burst Out DMA in all chaining descriptor

locations.

BA22_CHAN_RX_FIFO_COUNT

[0xC] RX [Master] FIFO data count (read only)

RX FIFO Data Count Port

Data Bit

Description

31-0

RX Data Words Stored

Figure 15 PcieBiSerialDb37BA22 RX FIFO data count Port

This read-only register port reports the number of 32-bit data words in the Receive FIFO
plus pipeline. The maximum count is the FIFO size plus 4.

BA22_CHAN_FIFO

[0x10] Write TX/Read RX FIFO Port

RX and TX FIFO Port

Data Bit

Description

31-0

FIFO data word

Figure 16 PcieBiSerialDb37BA22 RX/TX FIFO Port

This port is used to make single-word accesses to and from the FIFO.  Data read from
this port will no longer be available for DMA transfers. Writing to the port loads the Tx
FIFO, Reading unloads the Rx FIFO.

Two pixels are stored per LW.  Pixels are 14 bits.   Upper two bits per pixel for transmit
are ignored.   Upper two bits per pixel for Rx are reserved.

D31,D30, D29-D16, D15, D14 D13-0  The data transmitted and received for the D29-16
and D13-0 can be reversed orderwise to match your system memory situation.  See the
Data_Order control bits.  The receive data has an extra feature.   Bit 15/31 is set for the
pixel corresponding to one having the frame bit set.

«
...
29
30
31
32
33
...
»

Содержание PCIeBiSerialDb37-BA22













































Отзывы:

Нет отзывов

Похожие инструкции для PCIeBiSerialDb37-BA22

Бренд: D-Link Страницы: 113

Бренд: D-Link Страницы: 146

Бренд: Gardigo Страницы: 8

Бренд: Gardigo Страницы: 19

Бренд: Racal Instruments Страницы: 94

Бренд: Racal Instruments Страницы: 97

Бренд: Walimex Pro Страницы: 68

Бренд: jablotron Страницы: 22

Бренд: jablotron Страницы: 2

Бренд: Lawler Страницы: 4

Бренд: QTP Страницы: 2

Grafica DNE-K07

Бренд: Paradox Страницы: 24

Бренд: Panosol Страницы: 105

Бренд: Pangolin Страницы: 8

Бренд: Parker Страницы: 21

Бренд: Parker Страницы: 26

Бренд: Parallax Страницы: 3

Бренд: UniPOS Страницы: 51

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды