Dukane AiM iQ Series Скачать руководство пользователя страница 15

Страница: 15 / 67

Page 9

Section 2 – Installation

Dukane Manual Part No. 403-610-02

Connecting Cables

Details about the various system connectors and their pin

assignments are covered in

Section 3

The connections are the same for both the vertical and

horizontal generator configurations. However, the panel

location of the connectors differs between the two chassis

styles.

AC Power

Detached Cords

The AC line cords supplied with the standard generators

are matched to the ultrasonic output power rating and the

continent of specified use. See Table 2-I.

Attached Cords

240 Volt Single Phase Systems

- High power genera-

tors with power ratings above 2600W use permanently at-

tached power cords.

Table 2 - I

Standard IEC AC Power Cord Part Numbers

Continent of Use

Power Cord

Part Number

Power

North America

200-1109

120V, 15A

200-1110

240V, 15A

Continental Europe

200-1111

240V, 16A

The power cord is equipped

with a three-prong, ground-

ed-type plug for your safety.

Whenever a two-slot re-

ceptacle is encountered, we strongly

recommend that it is replaced with a

properly grounded three-lead receptacle.

Have a qualified electrician do the

replacement in accordance with the

National Electrical Code and local

codes and ordinances. DO NOT

cut off the power cord grounding

prong or alter the plug in any way.

CAUTION

Optional Plugs Available

NEMA L6-30P

Dukane part number 570-296

Figure 2-1 North American Plug

IEC 60309 (Sleeve 332P6)

Dukane part number 570-301

Figure 2-2 International Plug

Содержание AiM iQ Series




































































Результаты поиска

Содержание AiM iQ Series

Отзывы:

Похожие инструкции для AiM iQ Series

Бренды по названию

Популярные бренды

Dukane AiM iQ Series, Руководство пользователя

Результаты поиска

Содержание AiM iQ Series

Отзывы:

Похожие инструкции для AiM iQ Series

Бренды по названию

Популярные бренды