Dukane AiM iQ Series Скачать руководство пользователя страница 43

Страница: 43 / 67

Page 37

Section 4 – Standard System Status and Controls

Dukane Manual Part No. 403-610-02

ALARMS

Figure 4-12

Alarm Message Screen

Terminology

: Alarm refers to any fault, or error the gen-

erator might produce.

An alarm condition may occur. Figure 4-12 shows the

format for a typical alarm display.

The list below gives general reference information for

each alarm condition.

Table 4-I

Alarm Messages

NOTE

Go to this web address:

https://support.dukane.com/EasyAlarm

for more information about the alarm’s cause

and remedy.

Alarms

U100

Configuration Fault (The default setup may be corrupted, the model number does not match the generators installed

assemblies, the Serial Number is incorrect or missing.)

U104

Frequency Overload Fault 1 (The generator was unable to find the stacks frequency by twice the time of the Ramp Up

setting.)

U106

Peak Overload Fault (The generators output current has exceeded it’s safe operating level and has terminated the ultrasound

output.)

U108

Average Overload Fault (The output power has exceeded the rated power of the generator model.)

U110

Power not OK Fault (There is a problem with the AC line voltage.)

U111

Over Temperature Fault (Generator has exceeded its safe operating temperature limit.)

U112

Frequency Overload Fault 3 (There was excessive operating frequency drift due to heating of the stack. The operating

frequency is “far” away from the Free Running Frequency.)

U116

Ultrasound Voltage Overload (The actual transducer voltage exceeded the maximum expected value at 100% amplitude.)

Initiate Alarm

U302

Ultrasound Activation Input Activated at End of Cycle

U308

Generator Not Ready (The generator initialization process is not complete. The generator is not ready to activate the

Ultrasound output. The Automation Cycle Stop input is activated while activating the Ultrasound Activation input.)

Process Alarm

U401

Weld Time Set to Zero

U402

Weld Power Set to Zero

U403

Weld Energy Set to Zero

U404

Weld Distance Set to Zero

U405

Weld Position Set to Zero

U406

Max Trigger Time Set to Zero

U413

Max Trigger Time Exceeded (The trigger did not occur within the specified time limit.)

Содержание AiM iQ Series




































































Результаты поиска

Содержание AiM iQ Series

Отзывы:

Похожие инструкции для AiM iQ Series

Бренды по названию

Популярные бренды

Dukane AiM iQ Series, Руководство пользователя

Результаты поиска

Содержание AiM iQ Series

Отзывы:

Похожие инструкции для AiM iQ Series

Бренды по названию

Популярные бренды