Dukane AiM iQ Series Скачать руководство пользователя страница 35

Страница: 35 / 67

Page 29

Section 4 – Standard System Status and Controls

Dukane Manual Part No. 403-610-02

Front Panel Controls

This section introduces the

Series ultrasonic generator

AiM control panel and LCD display with this information:

• Functions of the panel components shown in Figure

4-1 below are discussed.

• These screen basics are introduced:

— Making selections,

— Interpreting on-screen arrows,

— Taking a look at setup identification.

NOTE

Do not touch the display.

Touch only the keys that are on the

front panel.

Cleaning - If the display is dirty, clean it

by first putting a mild cleaning solution

on a clean, soft cloth. Then, gently wipe

the cloth over the screen.

System

Operating

Mode

Keys (3)

Navigation Keys (4)

ENTER Key

CANCEL Key

INFO Key

System Power Output Level

Online/Offline/E-STOP Status

Figure 4 - 1

Front Panel Controls

Содержание AiM iQ Series




































































Результаты поиска

Содержание AiM iQ Series

Отзывы:

Бренды по названию

Популярные бренды

Dukane AiM iQ Series, Руководство пользователя

Результаты поиска

Содержание AiM iQ Series

Отзывы:

Бренды по названию

Популярные бренды