manualshive.com logo in svg

DT SWISS O.D.L., Техническое руководство

Поделиться
Скачать
DT SWISS O.D.L. Скачать руководство пользователя страница 28

O.D.L - Technical Manual

27

Setting the Damping

V2016.10

4.3

Setting the Damping

The correct setting of the damping requires some patience but the full potential of the fork can only be 
attained if the setting is perfect.

4.3.1

Rebound

The rebound controls the speed of the decompression movement.

To adjust the rebound damping, turn the red adjusting 
knob on the bottom of the right stanchion.

•

Turn clockwise to increase the rebound damping.

•

Turn anti-clockwise to decrease the rebound 
damping.

If the rebound damping is too low, the front wheel 
decompresses too fast and loses the contact to the ground. 
If the rebound damping is too high, the front wheel 
cannot follow fast impacts and the suspension hardens.
The aim of setting the rebound damping is to achieve the 
best setting possible, which meets the requirements of the 
terrain best. Rough, fast downhills require a low rebound damping, while flowy downhills without big hits 
require a higher damping.

Basic rebound setup: 12 clicks based on a fully opened damping.

Based on this setup, the user can fine tune the damping to fit specific needs.

If the weight of the rider is more than 75 kg/165 lbs, the rebound should be closed additional 2 to 5 
clicks. If the weight of the rider is clearly lower than 75 kg/165 lbs, the rebound should be opened 
additional 2 to 5 clicks.

Содержание O.D.L.































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды