DSC Power632 Скачать руководство пользователя страница 5

1

Section 1: System Introduction

1.1

Specifications

Downloading Software Support

PC1555MX v2.3 uses DLS-3 v1.3 and higher.

Flexible Zone Configuration

Six fully programmable zones

System expandable to 32 zones using:

up to 8 keypad zone inputs and/or 

up to 32 wireless zones with the PC5132 wireless expan-
sion module

38 access codes: one master code, one maintenance
code, two duress codes, two supervision codes and 32
general access codes

27 zone types; 8 programmable zone attributes

Normally closed, single EOL and double EOL zone wiring

Audible Alarm Output

700mA supervised bell output (current limited at 3A),
12V

DC

Steady or pulsed output

EEPROM Memory

Does not lose programming or system status on complete
AC and battery failure

Programmable Outputs

One programmable voltage output and one programmable
voltage output/input; 23 programmable options

PGM1 = 50mA; PGM2 = 300mA (50/300 products)

PGM2 = 50mA; PGM2 = 50mA (50/50 products)

Eight additional low current (50mA) outputs available using
the PC5208 module

Four additional high current (300mA) outputs available
using the PC5204 module; one PC5204 output fully super-
vised for siren 

Powerful 1.5 Amp Regulated Power Supply

550 mA auxiliary supply, 12 V

DC

Positive Temperature Coefficient (PTC) components
replace fuses

Supervision for loss of AC power, low battery

Internal clock locked to AC power frequency

Power Requirements

Transformer = 16.5 V

AC

, 40VA

Battery = 12 volt 4Ah minimum rechargeable sealed lead
acid battery

For household fire and burglary installations, two 7Ah bat-
teries in parallel must be used, providing 24 hours of
standby power and 4 minutes of alarm output power.

For commercial burglary installations, a 4Ah (or larger) bat-
tery must be used, providing at least 4 hours of standby
power and 4 minutes of alarm output power.

NOTE: 

 Do not install this panel outside of North America. By

design, this panel 

will not work

 if the AC line frequency drops

below 55.5Hz.

Remote Keypad Specifications

Keypads available:
- PC5502Z2 2-zone LED keypad with 2-zone inputs
- PC5506 six zone LED keypad with zone input
- PC5508Z eight zone LED keypad with zone input
- PC5516Z sixteen zone LED keypad with zone input
- PC5532Z thirty-two zone LED keypad with zone input
- LCD5500Z alphanumeric keypad with zone input
- LCD5501Z fixed message LCD keypad with zone input
- LCD5501Z32 keypad / receiver
- SL-8 Slimline 8 zone LED keypad

All keypads have five programmable function keys 

Connect up to eight keypads

4-wire (Quad) connection to Keybus

Built in piezoelectric buzzer

Digital Communicator Specifications*

Supports major communication formats including SIA and
Contact ID

Digital communicator compatible receivers and their for-
mats:
Silent Knight Model 9000: 3/1, 4/1, 4/2 non-extended, 3/1
extended, 20 bps, 1400 Hz handshake.
Ademco Model 685: 3/1, 4/1, 4/2 non-extended, 3/1
extended, 20 bps, 1400 Hz handshake, Contact ID.
Sescoa Model 3000: 3/1, 4/1, 4/2 non-extended, 3/1
extended, 20 bps, 1400 Hz handshake.
Radionics Model D6500: 3/1, 4/2 non-extended, 3/1
extended, with or without parity, 1400 and 2300 Hz hand-
shake. Sur-Gard Model MLR2-DG: 3/1, 4/1, 4/2, without
parity, 20 bps, 1400 and 2300 Hz handshake, Contact ID,
SIA.

Event-initiated personal paging

Three programmable telephone numbers

Two account numbers

Supports LINKS1000 cellular communication

Supports LINKS2X50 long range radio transmitter

Supports Skyroute transceiver

DTMF and pulse dialing

DPDT line seizure

Anti-jam feature

Split reporting of selected transmissions to each telephone
number

System Supervision Features

The PC1555MX continuously monitors a number of possible
trouble conditions including:

AC power failure• AUX Power Supply Trouble

Fault by zone• Loss of internal clock

Tamper by zone• Bell output trouble

Fire trouble• Telephone line trouble

Failure to communicate• Low battery condition (panel)

Low battery by zone (wireless)

Module fault (supervisory or tamper)

False Alarm Prevention Features

Audible Exit Delay• Quick Exit

Audible Exit Fault • Cross Zone Burglary Alarm

Communication Delay• Rotating Keypress Buffer

Urgency on Entry Delay• One Restart of Exit Delay

Additional Features

Auto Arm at specified time

Keypad-activated alarm output and communicator test

All modules connect to the system via a four wire Keybus
up to 1000’/305m from main panel

An event buffer which records the past 128 events with
both the time and date at which they occurred; buffer can
be printed using PC5400 serial interface module, or
viewed with the LCD5500Z keypad and DLS-3 software

Supports the addition of the PC5132 wireless receiver for
integration of wireless devices

Uploading and downloading capability

Local downloading capability through the use of the
PC-Link adaptor

Supports the Escort5580 Voice Prompt Module with auto-
mation/lighting control

Supports the addition of the PC5928 Audio Interface Mod-
ule to integrate intercom stations

*LINKS2X50 has not been investigated by UL.

Содержание Power632





















































Отзывы: