DSC Power632 Скачать руководство пользователя страница 30

Страница: 30 / 52

NOTE:

The Invalid Code Counter will be reset every hour.

To disable the keypad lockout option, program the Number of
Invalid Codes Before Lockout as [000].

NOTE:

If Keypad Lockout is active, the panel CANNOT be

armed / disarmed with a keyswitch.

Keypad Lockout Options. . . . . . . . . . . . . . . . . . Section [012]

5.22 Keypad Blanking

If the

Blank Keypad When Not in Use

option is enabled, the

panel will turn off all lights and LCDs on the keypads when no
keys are pressed for 30 seconds. The keys, however, will
remain backlit.
The panel will turn the lights and LCDs back on if entry delay
begins or an audible alarm occurs. The lights and LCDs will
also come on if a key is pressed or if a valid access code is
entered when the

Code Required to Restore Blanking

option is enabled.

NOTE:

If using a PC5132 v3.0 or higher, or PC5102 v1.0 or

higher and wireless keys, do not enable the Code Required to
Restore Blanking option, as the keys will not function correctly.

If the

Power Save Mode

option is enabled the panel will blank

all keypad lights including backlighting when AC power fails,
in order to conserve the backup battery.

Blank Keypad when not in use . . . . . . . . .   Section [016]: [3]
Code Required to Restore Blanking . . . . .   Section [016]: [4]
Power Save Mode . . . . . . . . . . . . . . . . . . .   Section [016]: [6]

5.23 Keypad Backlighting

The keys of all the keypads can be backlit to provide easy
viewing in dim lighting conditions. If the

Keypad Backlighting

option is enabled the keys will be illuminated.

Keypad Backlighting Option . . . . . . . . . . . . Section [016]: [5]

5.24 Loop Response

The normal loop response time for all zones is 500 millisec-
onds. The panel will not consider a zone violated unless it is
violated for at least 500 milliseconds.
Zones 1-6 on the control board, however, can be programmed
for a fast loop response (under 40ms).

Zones 1-6 are Fast Loop Response . . . . Section [030]: [1-6]

5.25 Keypad Tampers

If the

Keypad Tampers Enable

option is selected, the panel

will display and transmit a

General System Tamper

reporting

code if any keypad is removed from the wall. When the key-
pad tamper is restored, the panel will transmit the

General

System Tamper Restoral

reporting code. All keypads should

be properly installed and secured before enabling this option.

NOTE:

The auto-arm cancellation code is not transmitted

when a reset is required because a user has not cancelled the
auto-arming sequence.

Keypad Tamper Enable. . . . . . . . . . . . . . . . Section [016]: [8]
General System Tamper and Tamper
Restoral Reporting Codes . . . . . . . . . . . . . . . . . Section [338]

NOTE:

After enabling keypad tampers, it is recommended that

you tamper and restore all keypads to ensure proper function-
ing.

5.26 LINKS1000 Cellular Communicator

The LINKS1000 cellular communicator can be used three dif-
ferent ways:
•

as the sole communicator for the panel

•

as a backup for either or both telephone numbers

•

as a redundant backup to the land line communicator,
where the panel will call using the land line and the LINKS.

A LINKS Preamble is programmable for each telephone num-
ber in the event that the land line number is local but the
LINKS is required to dial an exchange. When programming a
LINKS Preamble, all unused digits must be programmed with
a hexadecimal ‘F’.

NOTE:

If a LINKS1000 is connected to the system, make sure

the

Maximum Number of Dialing Attempts

is programmed to

be 008 or greater (section [160].

Using LINKS1000 as the Sole Communicator

The panel can be programmed to report an event using only
the LINKS1000 cellular communicator. To program this option,
select only the LINKS1000 in the

Communicator Call Direc-

tion Options

. The

Call LINKS as well as Land Line

option

must also be enabled.
When the selected event occurs the panel will only attempt to
call central station using the LINKS.

Using the LINKS1000 as a Backup Communicator

The panel can be programmed to call using the LINKS1000
cellular communicator if the panel is having difficulty commu-
nicating an event using the land line. To program this option,
select both the telephone number and LINKS options in the

Communicator Call Direction Options

. The

LINKS is

Backup of Land Lines

option must be selected.

When used as a backup communicator, the panel will attempt
to call the central station in the following manner:
the panel will try to call using land lines – if unsuccessful, the
panel will try to call using the LINKS;
if unsuccessful, the panel will try to call using the land lines on
the next dialing attempt.
This process will continue until the panel has successfully
communicated with the central station or until the panel’s pro-
grammed number of dialing attempts has been exhausted.

Using the LINKS as a Redundant Communicator

The panel can be programmed to call using first the
LINKS1000 and then the land line when an event occurs. To
program this option, select both the telephone number and
the LINKS options for the

Communicator Call Direction

Options

for the event. The

Call LINKS as well as Land Line

option must be selected.

LINKS Special Preamble

In some areas of North America, dialing #DAT or *DATA
reduces the cellular billing increment. The

LINKS Special

Preamble

(section [393]), allows the use of [*] and [#] charac-

ters for the programming of #DAT and *DATA.
The

LINKS Special Preamble