Dräger Savina Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 132

Dräger Savina Скачать руководство пользователя страница 5

For your safety and that of your patients

5

For your safety and that of your
patients

Strictly follow the instructions for use

Any use of the apparatus requires full understanding and strict
observation of these instructions. The apparatus is only to be
used for purposes speciﬁed here.

Maintenance

This apparatus should only be inspected, serviced and
maintained by trained service personnel.
We recommend that a service contract be obtained with
DrägerService and that all repairs also be carried out by them.
Only authentic Dräger spare parts may be used for
maintenance. Observe chapter "Maintenance Intervals".

Accessories

Do not use accessory parts other than those in the order list.

Not for use in areas of explosion hazard

This apparatus is neither approved nor certiﬁed for use in
areas where combustible or explosive gas mixtures are likely
to occur.

Safe connection with other electrical equipment

Electrical connections to equipment which is not listed in
these instructions for use should only be made following
consultation with the respective manufacturer or an expert.

Liability for proper function or damage

The liability for the proper function of the apparatus is
irrevocably transferred to the owner or operator to the extent
that the apparatus is serviced or repaired by personnel not
employed or authorized by DrägerService or if the apparatus
is used in a manner not conforming to its intended use.
Dräger cannot be held responsible for damage caused by
non-compliance with the recommendations given above.
The warranty and liability provisions of the terms of sale
and delivery of Dräger are likewise not modiﬁed by the
recommendations given above.

Dräger Medical AG & Co. KGaA

«
...
3
4
5
6
7
...
»

Содержание Savina





































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды