manualshive.com logo in svg

Dräger Savina, Инструкция по эксплуатации

Поделиться
Скачать
Dräger Savina Скачать руководство пользователя страница 121

Technical data

121

Plateau time Tplat

Range

0 to 10 s

Resolution

0.1 s

Accuracy

0.1 s

Resistance R

Range

3 to 100 mbar/L/s

Resolution

1mbar/L/s

Accuracy

±2.5 mbar/L/s or 20 %, whichever is greater

Compliance C

Range

3 to 200 mL/mbar

Resolution

1 mL/mbar

Accuracy

±2 mL/mbar or 20 %, whichever is greater

Breathing gas temperature measurement
(NTC sensor)

Range

18 to 51 

o

C

Resolution

1 

o

C

Accuracy

±1 

o

C

Curve displays

Airway pressure Paw (t)

–5 to 100 mbar

Flow (t)

–200 to 200 L/min

Monitoring

Expiratory minute volume MV

Upper alarm limit alarm

when MV exceeds the upper alarm limit.

Setting range

41 to 2 L/min, in 0.1 L/min steps

Lower alarm limit alarm

when MV falls below the lower alarm limit.

Setting range

0.5 to 40 L/min, in 0.1 L/min steps

Airway pressure Paw

Upper alarm limit alarm

when the "Paw high" value is exceeded.

Setting range

10 to 100 mbar

Lower alarm limit alarm

when the value "PEEP +5 mbar" (coupled with the PEEP set value) 
is not exceeded for at least 0.1 s in two successive ventilation 
strokes

Delay time T

Disconnect

 for 

"Airway pressure lower alarm limit" alarm 
(only in »Mask/NIV« mode)

0 to 60 s

Insp. O

2

 concentration FiO

2

Upper alarm limit alarm

if FiO

2

 exceeds the upper alarm limit for at least 20 seconds.

Lower alarm limit alarm

if FiO

2

 falls below the lower alarm limit for at least 20 seconds.

Range

both alarm limits are automatically allocated to the set value:
below 60 vol. % with ± 4 vol. %
above 60 vol. % with ± 6 vol. %

Содержание Savina





































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды