Dormakaba LA GARD 700 Series Скачать руководство пользователя страница 18

Страница: 18 / 76

dormakaba USA Inc. System User Guide 7040.1121 Rev E 10/22 | 17

Event

Buzzer

LED

Screen Message(s) (Display Only)

Key press

Short beep

Short green or red flash High beep + Green flash = Valid Key

Low Beep + Red flash = Invalid Key

Valid command

response

3 short high beeps

3 short green flashes

Success

Invalid command

response

3 short low beeps

3 short red flashes

Invalid Message

Wrong Try Penalty

2 short low beeps

- every 10 seconds

2 short red flashes –

every 10 seconds

Wrong Try Penalty

ends

2 short high beeps

2 short green flashes

Time Delay

1 low beep – every

10 seconds

1 red flash – every 10

seconds

Time Delay

Confirm window

1 high beep –

every 10 seconds

1 green flash – every 10

seconds

Confirmation Window

Low Battery

2 low beeps

2 red flashes

Low Battery

Critical Low Battery

3 long low beeps

3 long red flashes

Critical Low Battery

Master Reset

3 short high beeps

3 short green flashes

Reset Success

Power On – No lock

connected

5 medium to low

beeps

5 medium red flashes

No Lock Found

Turn Power Off and Connect

Power On – Bad

configuration

5 medium to low

beeps

5 medium red flashes

Bad Config

Power On/Wake Up –

Lock Connected but

Not Installed

1 medium low

beep

Solid red LED

Lock Detected

Power On – Keypad

not compatible

1 long low beep

Continuous alternate

flashing red and green

Wrong Keypad Model Cannot

Install

Master reset

3 short high

beeps

3 short green flashes

Reset Success

3.3.1 System Info (Display Only)

The System Info screen provides information related to the Keypad and safe locks connected to the System,
including Firmware version and Model number.

Note:

This information is only available to authorized users.

Follow these steps to navigate through the System Info menu:

Содержание LA GARD 700 Series













































































Результаты поиска

Содержание LA GARD 700 Series

Отзывы:

Похожие инструкции для LA GARD 700 Series

Бренды по названию

Популярные бренды

Dormakaba LA GARD 700 Series, Руководство пользователя системы

Результаты поиска

Содержание LA GARD 700 Series

Отзывы:

Похожие инструкции для LA GARD 700 Series

Бренды по названию

Популярные бренды