Doosan DP158LCF страница 83 Скачать руководство пользователя

Страница: 83 / 160

6. Cooling system

117

General information

General Information

This engine is water-cooled. It uses coolant to cool the

engine by absorbing heat from the combustion chamber

and the engine oil and then releases the heat, allowing

for normal engine operation.

In this cooling system, coolant provided by the coolant

pump flows into the oil cooler through the coolant pipe

to absorb oil heat and passes through the coolant jacket

of the cylinder block and the cooling path of the cylinder

head to absorb the combustion heat.

Coolant which absorbed the oil and combustion heat

flows into the water temperature controller through the

coolant pipe. If the coolant temperature is lower than the

valve-opening temperature of the water temperature

controller, the coolant flows into the coolant pump. If

higher, it flows into the radiator. The radiator releases the

heat absorbed from the coolant and sends the coolant to

the coolant pump again.

DV2213098A

Specifications

Detail

Jacket

Heater

Port

M30

Jacket

Heater

Detail

Jacket

Heater

Port

M30

From

Jacket

Heater

OIL

OOLER

HEATER

LINDER

BLO

AIR

VENT

WATER

PUMP

PASS

THERMOSTAT
OPENING

Temperture

AIR

FLOW

WATER

RADIATOR

FILER

Positive

Pressure

kPa

Negative

Pressure

kPa

Item

DP158L

Remarks

DP158LCS

DP158LCF

DP158LDS

DP158LDF10

Cooling System

Cooling method

Fresh water forced circulation

Coolant capac-
ity (L)

Engine only

Approx. 20

With radiator

Approx. 79 (Air on 43°C) / Approx 90 (Air on 52°C)

Содержание DP158LCF

































































































































































Результаты поиска

Содержание DP158LCF

Отзывы:

Похожие инструкции для DP158LCF

Бренды по названию

Популярные бренды

Doosan DP158LCF, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание DP158LCF

Отзывы:

Похожие инструкции для DP158LCF

Бренды по названию

Популярные бренды