Doosan DP158LCF Скачать руководство пользователя

Страница: 131 / 160

10. Cylinder block/head

172

Cylinder head

Measurement of Cylinder Liner

1. Remove the cotter pin pressing the valve spring by

means of a special tool.

DV2213112A_E

2. Remove out the valve stem seal.

3. Remove the intake valve and the exhaust valve.

4. Remove the valve guide from the cylinder head

combustion with the special tool.

DV2213113A

Assembly of Cylinder Head

1. Clean the cylinder head.

2. Apply engine oil on the valve stem and the valve

guide, and then attach the valve.

3. Replace the new valve stem seal and then attach the

stem seal to the valve guide of the cylinder head with

the special tool.

4. Attach the valve spring washer to valve guide.

5. Put in the inner and outer spring and then attach the

valve spring plate on the springs.

6. Attach the valve cotter with the valve spring compress

tool.

7. Check if the valve cotters have been positioned

correctly with the plastic hammer after completing

attaching them.

DV2213114A

Check of Cylinder Head

1. Checking cylinder head

1) Check cracks or damage of the cylinder head.

2) Remove carbon from the bottom surface of the

cylinder head. Here, be careful not to scratch the

valve seat surface.

CAUTION

Be careful not to damage the cylinder gasket.

Valve Spring

ompression Tool

CAUTION

Be careful not to damage the valve stem seal.

CAUTION

The yellow mark on the valve spring is upward.

CAUTION

Be careful not to scratch the valve seat surface.

Содержание DP158LCF

































































































































































Результаты поиска

Содержание DP158LCF

Отзывы:

Похожие инструкции для DP158LCF

Бренды по названию

Популярные бренды

Doosan DP158LCF, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание DP158LCF

Отзывы:

Похожие инструкции для DP158LCF

Бренды по названию

Популярные бренды