Doosan DP158LCF страница 22 Скачать руководство пользователя

Страница: 22 / 160

4. Regular inspection

Replacement of Engine Oil

Check the oil level using an oil level gauge and replenish

it if required. Replace the engine oil in the following steps

when the engine is warm by running it.

1. Pull out the oil level gauge.

2. Open the drain plug of the oil pan to discharge the

engine oil from the container.

DV2213017A

3. After discharging the engine oil, assemble the drain

plug of ghe oil pan again.

4. Fill the engine oil into the cartridge of the oil filter.

5. Through the oil filler cap, fill the engine oil.

6. Idle the engine for several minutes so that the oil

circulate through the lubrication system.

7. Then, stop the engine, wait for about 10 minutes,

check the oil level, and fill the oil if required.

Replacement of Engine Filter

Check the oil pressure and leakage, and replace the oil

filter if required. Whenever replacing the oil, the oil filter

cartridge should be replaced with a new on.

1. Using an oil filter wrench, loosen the cartridge by

turning it counterclockwise.

2. Wipe the oil filter head and cartridge contact thor-

oughly, and make sure that the oil filter cartridge is

positioned properly.

3. Apply a little bit of oil to the o-ring area of the

cartridge, assemble it until the O-ring surface may

contact, and turn it 3/4 or 1 turn using a wrench to

keep it air-tight.

DANGER

•

Prolonged and repeated contact of skin with

engine oil may lead to shrinking, dryness of skin

and even cause dermatitis.

•

Do not expose skin with exchanged engine oil for

a long period.

•

Always wear work clothes and gloves.

•

When skin is stained with engine oil, immediately

wash it with water, soap or hand cleaners.

•

Do not clean skin with gasoline, fuel, thinner, or

solvent.

•

Apply a skin protective cream after cleaning from

oil.

•

Do not put oil-stained gloves or cloth in pockets.

WARNING

Discard exchanged oil according to the regulations

set forth by the relevant authorities. Disposing of

discharged oil into the ground, sewers, drains,

rivers, or the sea will cause serious environmental

pollution. Violation of regulations regarding discard

of engine oil without observing the handling regula-

tions, will be punished.

CAUTION

When replacing the oil filter cartridge, be sure to use

the genuine part of Doosan.

Содержание DP158LCF

































































































































































Результаты поиска

Содержание DP158LCF

Отзывы:

Похожие инструкции для DP158LCF

Бренды по названию

Популярные бренды

Doosan DP158LCF, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание DP158LCF

Отзывы:

Похожие инструкции для DP158LCF

Бренды по названию

Популярные бренды