Doosan DP158LCF Скачать руководство пользователя страница 67

Страница: 67 / 160

5. About the engine

100

1) Rotate the crankshaft so that the #1 cylinder piston

may be positioned at the top dead center(OT) and the

#6 cylinder piston may be posiitioned at the valve

overlap.

Note) In case of 8/12 cylinder engine, #6. cylinder is posi-

tioned at the valve overlap when #1. cylinder is

positioned at the compression TDC(Top Dead

Center).

Note) In case of 10 cylinder engine, #7. cylinder is posi-

tioned at the valve overlap when #1. cylinder is

positoned at the compression TDC(Top Dead

center).

2) Rotate the crankshaft until the yellow mark of the

camshaft gear is not shown.

3) Adjust the fuel injection timing with rotating the

flywheel to the engine rotating direction.

18. Attach the fuel injection driven gear temporarily.

DV2213186A

DV2213171A

1) Attach the driven gear(A) to the fuel injection pump

temporarily.

2) Attach the O-ring(B) and (C) to the fuel injection

pump.

3) Align the injection timing pointer of the fuel injection

pump driven gear with the marking on the cylindrical

surface.

Engine Model

Fuel Injection Timing (

)

DP158L

DP158LCS

DP158LCF

DP158LDS

DP158LDF

DP180L

DP180LBS

DP180LBF

DP180LAS

DP180LAF

DP222L

DP222LAS

DP222LBS

DP222LBF

DP222LCS

DP222LCF

Содержание DP158LCF

































































































































































Результаты поиска

Содержание DP158LCF

Отзывы:

Бренды по названию

Популярные бренды

Doosan DP158LCF, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание DP158LCF

Отзывы:

Бренды по названию

Популярные бренды