Doosan DP158LCF Скачать руководство пользователя страница 64

Страница: 64 / 160

5. About the engine

8. Attach the oil seal to the front oil seal cover.

DV2213183A

1) Apply engine oil on the surface of the oil seal rotation

contact.

2) Install the oil seal to the front oil seal assembly jig

(EF.120-030).

3) Align the front oil seal assembly jig with the oil seal

hole of the front oil seal cover.

4) Attach the oil seal to the front oil seal cover and beat

the rear part of the front oil seal assembly jig with a

rubber hammer.

5) Pull off the front oil seal assembly jig.

9. Attch the front oil seal cover.

DV2213090A

1) Attach the front oil seal cover(B).

2) Tighten 6 M8 fixing bolts(A) at a tightening torque

2.24 kgf

10. Change the engine position.

DV2213184A

1) Change the engine positon. The flywheel direction is

downward.

11. Attch the cylinder liner.

DV2213089A

1) Apply enfing oil on the surface of the cylinder liner.

2) Attach the cylinder liner(A) to the cylinder block with

the cylinder liner puller(EF.123-365).

3) Attach 12 cylinder liners as the same procedure.

CAUTION

•

Be careful not to damage the oil seal.

•

Do not reuse the oil seal.

Содержание DP158LCF

































































































































































Результаты поиска

Содержание DP158LCF

Отзывы:

Бренды по названию

Популярные бренды

Doosan DP158LCF, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание DP158LCF

Отзывы:

Бренды по названию

Популярные бренды