Doosan DP158LCF Скачать руководство пользователя страница 50

Страница: 50 / 160

5. About the engine

6. Remove the alternator.

DV2213055A

1) Loosen the fixing nut(A) and bolt(B).

2) Remove the alternator(C).

7. Remove the alternator bracket.

DV2213056A

1) Loosen the fixing bolt(A) and then remove the

eyebolt(B).

2) Loosen the fixing bolt(C) and then remove the alter-

nator bracket(C).

8. Remove the inlet elbow.

DV2213057A

1) Loosen the hose clamp(A).

2) Loosen the V-clamp(B).

3) Remove the inlet elbow(C).

4) Remove the other side elbow as the same procedure.

9. Remove the oil delivery pipe.

DV2213058A

1) Loosen the the fixing bracket bolts(A) of the oil

delivery pipe.

2) Loosen the fixing bolts(B) of the oil delivery pipe.

3) Loosen the hollow screw(C).

4) Remove the oil delivery pipe(D).

CAUTION

Be careful not to loss the O-ring and insert parts

when removing the inlet elbow.

CAUTION

Be careful not to loss the O-ring and the gastket.

Содержание DP158LCF

































































































































































Результаты поиска

Содержание DP158LCF

Отзывы:

Бренды по названию

Популярные бренды

Doosan DP158LCF, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание DP158LCF

Отзывы:

Бренды по названию

Популярные бренды