Doosan DP158LCF Скачать руководство пользователя

Страница: 69 / 160

5. About the engine

102

3) Attach the vavle(B).

4) Attach the valve spring(E).

5) Compress the valve with the valve spring press

(EF.120-262).

6) Attach the valve cotters(F).

23. Attach the cylinder head assembly.

DV2213077A

1) Attach the gasket assembly.

2) Attach the cylinder head assembly(B).

3) Tighten 6 cylinder head fixing bolts(A) at a tightening

torque 8kgf

m + 15kgf

m + 90

+ 90

by using the

angle method.

4) Attach 12 cylinder head assembly as the same proce-

dure.

24. Attach the push rods.

DV2213076A

1) Attach 24 push rods(A).

25. Attach the rocker arm assembly.

DV2213075A

1) Attach the rocker arm assembly(B).

2) Tighten the fixing bolts(A).

3) Attach 12 rocker arms as the same procedure.

26. Attach the injectors.

DV2213073A

CAUTION

Be careful to use the right valve without confusing

the intake valve with the exhaust valve. The intake

valve is the mark “ I ” engraved on the head and

the exhaust valve is the mark “ E ” engraved on the

head.

CAUTION

Be carful the valve direction. The yellow mark on the

valve is upward.

CAUTION

Check if the valve cotters have been positioned

correctly with the plastic hammer after completing

attaching them.

Содержание DP158LCF

































































































































































Результаты поиска

Содержание DP158LCF

Отзывы:

Похожие инструкции для DP158LCF

Бренды по названию

Популярные бренды

Doosan DP158LCF, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание DP158LCF

Отзывы:

Похожие инструкции для DP158LCF

Бренды по названию

Популярные бренды