background image

6050-065-C-2-16

11

Arm 

Rotation Area 

Closed Gate 

5” 

1.5 Post Mount 

1.6 Arm and Gate Bracket Installation 

10”

18.5”

34” 

6”

Do not

 insert the locking pin or padlock 

into the crank arm. It will be installed 
after arms have been adjusted. 

Do not

 secure the elbow assembly 

to the arms until the arms have 
been adjusted. (See next page). 

Mount the post base into the concrete 
before installing the operator. 
 
The post mount installation will allow 
the operator to be mounted low enough 
to attach the gate bracket to the lower 
gate rail if desired. 

Adjust the locknut on the crank power 
arm so that it is snug against the 
washer, but will still allow the crank arm 
to rotate with little force. 

This is the 

operator’s manual release option when 
the crank arm is unlocked. 

Assemble arms as shown with the gate in the 

closed 

position.

 The elbow assembly’s flange 

MUST

 be on the 

opposite side of the gate in the closed position. 

This is 

the physical stop used to set the open and close limits. 

Concrete

Position

Gate Rail 

Run all conduit on the opposite 
side of the open gate.

Install gate 
bracket to gate. 

30” Crank Arm 

60” Connecting Arm 

Flange 

Crank Power Arm 

Elbow 
Assembly 

Point arms towards 
gate bracket. 

Gate Hinge Pivot Point 

Arms MUST be level. 

This distance can vary (6” minimum). 

Varies 

60” Connecting Arm 

Gate 

Bracket 

26”

Conduit

2”

43”

Post Base

Open Gate

Closed Gate

90°

Depth of the concrete pad is 
determined by soil conditions and 
local building codes. Reinforced 
concrete recommended. 

Gate Bracket Height 

Low 
Volt 

High 
Volt 

Inter

connection 

Cable 

Operator MUST 
be level.

5” 

12”

Note: 2” thick

gate Illustrated.

Concrete

Output Shaft

Содержание 6050-080











































Отзывы: