DoorKing 6050-080 Скачать руководство пользователя | Manualshive

Страница: 13 / 42

background image

6050-065-C-2-16

9

1.2 Post Mount or Pad Mount Base Assembly

Hardware for Pad Mount:

Pad Support Base

Post Support Base

(6) 1 inch bolts, lockwashers and nuts for support legs.

(2) 1 inch bolts and nuts for support plate.

(2) 1 1/2 inch bolts and nuts. For support plate.

(3) Non-slip nuts. For existing threaded studs on bottom of operator.

(2) 1 1/2” bolts through the main

gear bracket mounting holes.

(2) 1 1/2” bolts through the main

gear bracket mounting holes.

(2) 1” bolts through the main gear bracket mounting holes.

(2) 1” bolts through the main
gear bracket mounting holes.

Hardware for Post Mount:

(2) 1 1/2 inch bolts. For support plate.

(2) 1 inch bolts. For support plate.

(3) Non-slip nuts. For existing threaded

studs on bottom of operator.

Remove the cover from the
operator and

GENTLY

place

the operator on its side before
attaching the pad base.

Screw the posts to the support
plate and mount into concrete

BEFORE

attaching the operator.

Bottom of Operator

Bottom of Operator

Support

Plate

Support

Plat

e

Left Support Leg

1” Bolts

Right

Support

Leg

«
...
11
12
13
14
15
...
»

Содержание 6050-080











































Отзывы:

Нет отзывов

Похожие инструкции для 6050-080

Gate Control BASE 1000 Series

Бренд: tell Страницы: 55

Бренд: Roger Страницы: 8

Smart Phone Control

Бренд: Automatic Technology Страницы: 4

Power Drive Security+ HD200CD

Бренд: Chamberlain Страницы: 80

Automatic Technology Battery Backup Gen 2...

Бренд: B&D Страницы: 8

Safety Signal 3800RGD

Бренд: Raynor Страницы: 36

Бренд: FAAC Страницы: 8

Бренд: Motorline professional Страницы: 8

Бренд: GTO Страницы: 33

Бренд: Calimet Страницы: 24

Бренд: Black & Decker Страницы: 8

Gizmo EM200 Series

Бренд: Black & Decker Страницы: 2

Elixo 500 3S io

Бренд: SOMFY Страницы: 80

Home motion Dexxo Pro io

Бренд: SOMFY Страницы: 80

Бренд: Nice Страницы: 2

Бренд: E.T. Systems Страницы: 8

Бренд: Ghost Controls Страницы: 3

Бренд: Roger Technology Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды