DoorKing 6050-080 Скачать руководство пользователя

Страница: 14 / 42

6050-065-C-2-16

1.3 Underground Conduit Requirements

1.4 Pad Mount

Sweeps

Concrete Pad

Primary

Operator

Position

Secondary

Operator

Position

22”

24”

Depth of the concrete pad is
determined by soil conditions and
local building codes. Reinforced
concrete recommended.

Note: If allowed by local codes, the
top of the concrete pad can be flush
with ground level, which will allow
the gate bracket to be mounted
lower on the gate.

Arm

Rotation

Area

Gate Bracket Height

Concrete Pad Position

3/8

Secure the operator to the
concrete pad with four (4)
3/8” x 3” sleeve anchors
(not supplied).

Note: 2” thick

gate Illustrated.

Closed Gate

Open Gate

3”

Output
Shaft

3”

2.5”

Right Support Leg

Left Support Leg

Operator MUST
be level.

Note: Right support leg removed from
this illustration to show conduit detail.

Low
Volt

High
Volt

Inter

connection

Cable

11”

Conduit

5”

9.5” 6”

43”

12”

Pad Support Base

Concrete Pad

14”

10”

90°

DoorKing’s Primary/Secondary Interconnection Cable (Dual Operator Application Only)

(Secondary Operator AC Power and Communication wires)

Loop Lead-In Wires (Low Voltage wire insulation)
AC Input Power (High Voltage wire insulation)

•

The conduit requirements are for a typical slide gate operator installation (the secondary operator is shown for those

applications where a secondary operator may be used).

The conduit requirements for your application may vary from this

depending on your specific needs.

•

Use only sweeps for conduit bends. Do not use 90° elbows as this will make wire pulls very difficult

and can cause damage to wire insulation. DoorKing recommends using 3/4-inch conduit.

• Installation of

External Entrapment Protection Devices

is REQUIRED (photo sensor and/or reversing edge).

•

Be sure that all conduits are installed in accordance with local codes.

•

Never

run low voltage rated wire insulation in the same conduit as high voltage rated wire insulation.

Elbow

Sweep

YES

External Safety Devices, Controls and P.A.M.S. Wires (Low Voltage wire insulation)

Содержание 6050-080











































Результаты поиска

Содержание 6050-080

Отзывы:

Похожие инструкции для 6050-080

Бренды по названию

Популярные бренды

DoorKing 6050-080, Инструкция по установке и эксплуатации

Результаты поиска

Содержание 6050-080

Отзывы:

Похожие инструкции для 6050-080

Бренды по названию

Популярные бренды